Dear All
114Q for the 300-075 exam is still valid.
Passed today with 969/1000
Brugge
November 30th, 2015
New 300-070 Exam Questions and Answers Updated Recently:
NEW QUESTION 72
What are the two benefits of using SIP dial rules on an IP phone? (Choose two)
A. The phone can initiate dialing without sending any signaling messages to Cisco Unified CommunicationsManager.
B. The phone can detect invalid numbers and play a reorder tone without sending any signaling messages toCisco Unified Communications Manager.
C. If dialed digits match an entry of a SIP dial rule, the dialed string is sent in a single SIP 200 OK message toCisco Unified Communications Manager.
D. If Cisco Unified Communications Manager requires more digits, KPML can be used to send the remainingdigits from the SIP phone to Cisco Unified Communications Manager one-by-one.
E. If Cisco Unified Communications Manager requires more digits, another en bloc message is used to sendthe remaining digits from the SIP.
Answer: BD
NEW QUESTION 73
Which three Cisco Unified CallManager configuration steps are required to support third party SIP phones? (Choose three.)
A. Configure the device in Cisco Unified CallManager.
B. Change the proxy address in the SIP phone to an IP address or the Fully Qualified Domain Name (FQDN)of Cisco Unified CallManager.
C. Associate the device with the end user.
D. Configure the phone with the TLS username and password.
E. Configure the end user in Cisco Unified CallManager.
F. Add the MAC address of the Cisco Unified CallManager server to the SIP phone configuration page.
Answer: ACE
NEW QUESTION 74
Which four software based media resources require that the Cisco IP voice media stream Application be activated?
A. MOH.
B. SIP.
C. H.323 Gateways.
D. Annunciator.
E. Gatekeeper.
F. MTP.
G. Audio conferencing.
Answer: ADFG
NEW QUESTION 75
Which protocol is recommended to be used between Cisco Unified Communications Manager and the voice gateway to simplify the dial plan?
A. SIP.
B. SCCP.
C. H323.
D. RSVP.
E. MGCP.
Answer: E
NEW QUESTION 76
Which protocol can Cisco Unified Communications Manager not use to monitor the status of the gateway?
A. H.323
B. SIP
C. MGCP
D. SCCP
Answer: A
NEW QUESTION 77
In a centralized call-processing solution, there are five sites connected through an IP WAN. To optimize the utilization of the IP WAN, CAC needs to be implemented. How should CAC be implemented?
A. Use a gatekeeper to control allocated bandwidth properly.
B. Use locations CAC with a single location.
C. Use a gatekeeper and Cisco Unified Border Element to provide CAC to sites that use a combination of SIPand MGCP gateways.
D. Use a gatekeeper to only control those locations that use H.323 gateways and a Cisco Unified BorderElement to control those sites that use MGCP or SIP gateways.
E. Use locations CAC with five locations in addition to Hub none.
Answer: E
NEW QUESTION 78
Which two features are advantages of deploying a cluster over WAN? (Choose two.)
A. Shared line appearances
B. CentralizedDSP resources
C. Extension mobility within the cluster
D. Scalability up to 20 sites, if thereis sufficient IP WAN bandwidth
E. Failover to co-resident Cisco UnifiedCall Manager Express platforms
Answer: AC
NEW QUESTION 79
The Ajax Corporation is designing an IP telephony network using Cisco MCS 7845 Series servers, each one capable of supporting 7500 devices. The design must meet these requirements:
– Be cost-effective
– Support up to 7500 phones
– Provide a minimal level of redundancy
Which configuration will meet Ajax Corporation needs?
A. Two Cisco Unified Communications Manager servers:
1 publisher and TFTP server combined.
1 primary subscriber.
B. Three Cisco Unified Communications Manager servers:
1 publisher and TFTP server combined.
1 primary subscriber.
1 backup subscriber.
C. Four Cisco Unified Communications Manager servers:
1 publisher.
1 TFTP server.
1 primary subscriber.
1 backup subscriber.
D. Five Cisco Unified Communications Manager servers:
1 publisher.
1 TFTP server.
1 primary subscriber.
2 backup subscribers.
Answer: B
NEW QUESTION 80
How are Cisco Unified CallManager location parameters used?
A. Assign directory numbers to devices as they connect to the IP telephony network.
B. Specify the bandwidth used for audio and video calls.
C. Implement call admission control in a centralized call processing deployment.
D. Provide alternate call routing when the primary call path is unavailable.
Answer: C
NEW QUESTION 81
Which statement regarding Cisco IP voice media streaming application is correct?
A. It should be activated on the gateway in cluster that supports the TFTP service.
B. It should be activated on the gatekeeper in cluster that supports the TFTP service.
C. It should be activated on the node in cluster that does not support the TFTP service.
D. It should be activated on the node in cluster that supports the TFTP service.
Answer: D
NEW QUESTION 82
Which option describes how you add software conference bridges to Cisco Unified Communications Manager?
A. By adding a Cisco Unified CM server to the cluster.
B. By adding a software conference bridge using Conference Bridge Configuration.
C. By installing DSP to a Cisco Unified CM server.
D. By reassigning other media resources to conference resources.
Answer: A
NEW QUESTION 83
Which of these media resources can be configured in Cisco Unified Communication manager? (Choose Three)
A. MOH Server
B. Voice Termination Point DSP
C. Transcoder
D. Auto Attendant
E. Conference Bridge
Answer: ACE
NEW QUESTION 84
What is the relationship between a Region and a Location?
A. The Region codec parameter is used between a Region and its configured Locations.
B. The Region setting for a Location sets the number of audio and video calls that Location can support.
C. The codec parameter configured in the Region is only used between Regions and Location bandwidth isonly used between Locations.
D. The Region codec parameter is combined with Location bandwidth when communicating with otherRegions.
Answer: C
NEW QUESTION 85
……
BTW, These New 300-070 Exam Questions Were Updated By PassLeader, You Can Get The Newest 300-070 Dumps In PDF And VCE From — http://www.passleader.com/300-070.html
Good Luck !!!
Brugge
November 30th, 2015
New 300-085 Exam Questions and Answers Updated Recently:
NEW QUESTION 61
Which CCC action applies only to the Cisco TelePresence MPS Series?
A. block fast update requests
B. Status Duo Video
C. move back
D. release floor
Answer: A
NEW QUESTION 62
Which protocol is prioritized by Cisco TMS for conferencing?
A. SIP
B. MGCP
C. H.323
D. SCCP
Answer: C
NEW QUESTION 63
How does Cisco TMS set up a call with an endpoint that is registered with Cisco Unified Communications Manager and that is connected to Cisco VCS?
A. Cisco TMS uses an IP dialing plan.
B. Cisco TMS uses a SIP trunk.
C. Cisco TMS removes the top-level domain from calls that go through Cisco Unified Communications Manager.
D. Cisco TMS drops the call, because it can verify that the trunk between Cisco Unified Communications Manager and Cisco VCS is down.
Answer: B
NEW QUESTION 64
On Cisco TelePresence Management Suite, which two call control devices are supported for call control and setup? (Choose two.)
A. Cisco Unified Communications Manager Express
B. Cisco TelePresence Video Communication Server
C. Cisco Unified Border Element
D. Cisco Unified Communications Manager
E. any SIP-capable call control system
Answer: BD
NEW QUESTION 65
Which three are valid system connectivity statuses for systems that are automatically added to Cisco TelePresence Management Suite? (Choose three.)
A. Inaccessible
B. Failed
C. Connected
D. Reachable on Public Internet
E. Behind Firewall
F. Online
G. Remote Site
Answer: ADE
NEW QUESTION 66
To have a Provisioning menu section available on Cisco TelePresence Management Suite, what must you do?
A. You must configure an active ISDN zone.
B. You must install Cisco TelePresence Management Suite Provisioning Extension and activate it on the system.
C. You must license Cisco TelePresence Management Suite Analytics Extension.
D. You must set up Cisco TelePresence deployment to support Cisco CMR Hybrid.
Answer: B
NEW QUESTION 67
Which two actions must you take to enable provisioning on Cisco TMS and Cisco VCS? (Choose two.)
A. Apply a Device Provisioning option key on Cisco VCS.
B. Enable provisioning on Cisco VCS under Applications > Provisioning.
C. Configure Users, FindMe, Phonebooks, and Devices individually, as these all have different settings.
D. Configure a separate server to run provisioning extension services.
E. Ensure that a service account is able to connect.
F. Set the polling intervals on Users, FindMe, Phonebooks, and Devices to the same value, in order for the synchronization to work.
Answer: AE
NEW QUESTION 68
What must you do to activate the provisioning feature on a Cisco VCS endpoint?
A. Install the Device Provisioning option key.
B. Set a SIP trunk between Cisco VCS and Cisco Unified Communications Manager.
C. Add the Cisco VCS on the Cisco TMS, and enable Cisco Extension Mobility.
D. Install Cisco VCS Starter Pack Express.
Answer: A
NEW QUESTION 69
Refer to the exhibit. Which statement about the jabber-config.xml partial output is true?
A. 10.255.10.10 is the LDAP server address.
B. The client connects to the directory server by using SSH.
C. 10.255.10.10 is the Cisco Unified Communications Manager IM and Presence Service address.
D. The client connects to the directory server by using HTTPS.
Answer: D
NEW QUESTION 70
The UDS for contact resolution is enabled in the service profile configuration of the Cisco Unified Communications Manager. Which action can you execute with your Jabber Desktop?
A. modify users
B. search users
C. change users
D. delete users
Answer: B
NEW QUESTION 71
Which profile must you add to an end user record, if the end user wants to access voicemail and wants to control a deskphone via CTI with Cisco Jabber?
A. remote destination profile
B. device profile
C. SIP profile
D. service profile
E. phone service
Answer: D
NEW QUESTION 72
……
BTW, These New 300-085 Exam Questions Were Updated By PassLeader, You Can Get The Newest 300-085 Dumps In PDF And VCE From — http://www.passleader.com/300-085.html
Good Luck !!!
Brugge
November 30th, 2015
New 300-080 Exam Questions and Answers Updated Recently:
NEW QUESTION 76
Phone A is able to dial the directory number of Phone B and complete a call. However, when Phone B dials the directory number of Phone A, Phone B receives a fast-busy tone. What is causing this issue?
A. Phone A and Phone B are in different partitions.
B. Phone B does not have Phone A in its partition.
C. Phone B is not in the CSS of Phone A.
D. Phone B does not have the CSS of Phone A in its partition.
E. Phone B is not registered.
F. Phone B has the incorrect CSS to dial Phone A.
Answer: F
NEW QUESTION 77
An inbound call from the PSTN is not reaching the directory number that it is calling. When the PSTN phone calls the correct DID, only a dial tone is heard. Which command resolves this issue?
A. (config-dial-peer)#direct-inward-dial
B. (config-controller)# no provide-outside-dialtone
C. (config-if)#no dial-tone
D. (config-dial-peer)# no dial-tone
E. (config-if)#direct-inward-dial
F. (config) allow inbound dial-peer 1
Answer: A
NEW QUESTION 78
When a caller dials 9 plus an external seven-digit number, the caller hears a fast-busy tone after a period of silence. What is causing the silence?
A. There is no dial route for 9XXXXXXX on Cisco Unified Communications Manager.
B. The gateway is not dropping the leading 9, and the PSTN fails.
C. The T302 timer is waiting to expire.
D. The caller does not have the PSTN partition in the CSS.
E. The caller dialed the wrong number.
F. To dial successfully, the caller must enter a Forced Authorization Code.
Answer: C
NEW QUESTION 79
In a single-site deployment model, the internal endpoints are unable to dial from one to the other. What are two possible causes? (Choose two.)
A. The PSTN gateway is not configured.
B. The called endpoint does not have the SIP trunk enabled.
C. The called endpoint is not registered.
D. The calling endpoint is not in the CSS of the called endpoint.
E. The called endpoint is not in the partition of the calling endpoint.
F. The calling endpoint is not configured for the correct CoS.
Answer: CF
NEW QUESTION 80
What is the default interval for SAF hello packets?
A. 15 seconds
B. 15 seconds on links with speeds that are slower than T1 speeds
C. 40 seconds
D. 40 seconds onlinks with speeds that are slower than T1 speeds
E. 60 seconds
F. 60 seconds onlinks with speeds that are slower than T1 speeds
Answer: F
NEW QUESTION 81
Which configuration can be dynamically set using the Cisco Unified Communications Manager Device Mobility feature?
A. phone model and protocol
B. SRST reference and directory number
C. CSS and local gateway
D. partition and CSS
E. media resources and permanent bridges
Answer: C
NEW QUESTION 82
Which configuration is required on Cisco TelePresence Server, in order to support 1080p resolution?
A. Screen licenses must be configured.
B. Cisco TelePresence Server must be in remotely managed mode.
C. Cisco TelePresence Server must be in HD mode.
D. Cisco TelePresence Server must be configured with Cisco TelePresence Conductor.
E. Cisco TelePresence Server must be in Full HD mode.
Answer: E
NEW QUESTION 83
A user is dialing an external PSTN number with a prefix of 01 from a Cisco TelePresence SX10 Quick Set in a Cisco VCS environment. In the past, the Cisco VCS and the ISDN gateway were correctly configured with a prefix of 01, but the calls are now failing. What are three possible causes? (Choose three.)
A. The Cisco VCS Control is down.
B. The interworking setting is turned off.
C. The audio feature in the Cisco TelePresenceSX10 is turned off.
D. The SIP trunk is not configured on the gateway.
E. 01 is not a valid prefix.
F. ISDN is not enabled on the Cisco TelePresenceSX10.
G. The Cisco TelePresenceSX10 is not registered to the Cisco VCS Control.
H. The Cisco TelePresenceSX10 is not registered to the Cisco Express C.
Answer: ABG
NEW QUESTION 84
When the command utils dbreplication status is executed on the Cisco Unified Communications Manager CLI, which step should be taken next to check the database replication status?
A. View the activelog file.
B. Run the same command on all nodes of the cluster.
C. Restart the Cisco CallManager service.
D. The command utils dbreplication runtimestate must be run on the publisher.
E. The command utils dbreplication runtimestate must be run on the subscriber.
Answer: A
NEW QUESTION 85
Which tool can you use to see SAF advertisements in Cisco Unified Communications Manager?
A. Cisco Unified Real-Time Monitoring Tool
B. show eigrp neighbors command
C. debug eigrp commands
D. Terminal Monitor
Answer: A
NEW QUESTION 86
URI dialing is enabled between two clusters with the default options. The engineer that set up the URI dialing verified that all was working properly. However, a user from one of the clusters cannot dial using URI to a user in the same cluster. What do you do to resolve this issue?
A. Verify the password that is used by the authentication under Intercluster Lookup Service configuration.
B. Find out if the URI address of the called user has a capital letter in the URI string.
C. Verify that Intercluster Lookup Service is set up correctly.
D. Verify USN Data Synchronization Status.
Answer: B
NEW QUESTION 87
……
And, These New 300-080 Exam Questions Were Updated By PassLeader, You Can Get The Newest 300-080 Dumps In PDF And VCE From — http://www.passleader.com/300-080.html
Good Luck !!!
M@ne
November 30th, 2015
Hello Everyone!
Has it updated?
Rahul S
December 1st, 2015
Has anyone cleared the 300-075 exam in the last 2 days, want to ensure if dumps have changed or not!
Anonnano
December 3rd, 2015
Yes… 114Q was valid.
M@ne
December 7th, 2015
Any Updates?
Mansour
December 7th, 2015
Hi ,all
I attend the exam 300-075 and actual test 114 Q is still valid thank you for any one who shared the pdf file .
Scored 9XX/1000
All question is from the dump
the passing score is 860
Which protocol can Cisco Unified Communications Manager not use to monitor the status of the gateway?
A. H.323
B. SIP
C. MGCP
D. SCCP
Where is the Answer: A documented?
I will be taking mine before year end – thX !
M@ne
December 8th, 2015
Hello Everyone!
Are there new questions on exam?
karim
December 10th, 2015
what are the new questions in the exam that are not in the dump?
Kain
December 10th, 2015
@Mansour:
Thanks for the VCE. I’ve worked through a little over 1/3 of it looking up each answer and filling in the Explanation and Reference. I’ve found some mistakes:
Your Question 2 should be A instead of B (Same as in Actualtests which has A) per Cisco TelePresence Video Communication Server Administrator Guide (X8.5.1) Page 474 of 563.
I think question 40 is wrong (both Actualtests and VCE). I cannot find any references to multiple autonomous systems in the Cisco docs, but I do find reference that the client label in CUCM must match what’s on the SAF router. Cisco Unified Communications Manager Features and Services Guide, Release 9.1(1) Page 80.
Can anyone confirm or deny question 40???
Kain
December 10th, 2015
Also regarding question 40, The same doc says:
Autonomous System
All Cisco Unified Communications Manager clusters are limited to advertised or learned routes within the same autonomous system (AS).
Luis
December 11th, 2015
Hello Guys, anyone knows if the actualtest 114Q is still valid? Please Help!, I’m gonna take the exam next monday.
I uploaded a complete VCE to examcollect using the actual + Q72-84 from here but is has not shown up yet
driz
December 12th, 2015
colleague and i took and failed the 300-075 yesterday. 781 for myself 708 for him. We both knew the 114Q inside and out. Saw many SAF questions, port for mgcp and MTP questions (which i actually found answers to on the CCIE Collab MTP video from INE)
Anonymous
December 12th, 2015
hello guys
I lost my exam, there are many new questions
Anonymous
December 13th, 2015
Hello Friends I just gave my exam and failed with 750 score passing score was 860 with 75 Minutes to finish this exam. I did preparation from Actualtest 114Q and PassLeader 146Q only 10 to 15 questions came from them all new question. Don’t book your exam until you have correct answers otherwise its waste of Money Thanks
Samy Adly
December 14th, 2015
Hello, is the 114q dump still valid?
Anonymous
December 14th, 2015
Anonymous
Can you describre a little about these new questons?
Thank You.
driz
December 14th, 2015
lot’s of SAF, MTP questions (that i’ve seen in CCIE Collab INE Videos), typos, grammar issues.. All in all, this revamp was very poorly done. it was 52 questions instead of 60 though. i had 12 from the 114Q, everything else was new.
The ones who have given the exam recently last week…can you please let me know whether the brain dump is Ok.?.because i need to give the exam be fore dec 31st …
karim
December 15th, 2015
@Abhijeet no the dump by Kink is not including the new questions in the exam – reschedule your exam or you will lose your money
driz
December 15th, 2015
@Abhijeet i also just looked through your dump and i didnt see anything on it that wasn’t already on the 114Q. suggest you take a different CCNP exam to renew.
Passleader support is claiming to have a new version out tomorrow of the 300-075 if that is true I will download the PDF and send it to whoever needs it, it states their current version with 146Q is updated as of 12/22 but that cant be true as the last modified date of the .vce and .pdf file once you download it states 10/5. My exam is tomorrow so hopefully I can study some of the new version if its released before the test, I am not big on dumps, but there is no OCG on this exam, it does not release until March 2016 so I dont get how Cisco came out with a new exam in October? Plus my CCNP Voice expires 1/10/16 so I need to pass now.
Fitz
December 31st, 2015
Well I got the passleader.com 300-075 guide with 277Q it was supposed to be updated and it definitely is, its more updated than anything else I have, but I memorized all 277Q before my exam today and only 10 or 15 questions were on the exam. I am not sure where to get any more training material, I got a 759 and failed, you need a 860 to pass. Most of the questions I got right I knew from on the job experience, others were a guess, I studied some materia of of Cisco Learning Network but there is not much on there for this. There were alot of questions about SAF, ILS, CAC,SRST,RSVP Bandwidth and Region questions, VCS Control and VCS Expressway ad Device Mobility questions as well, Study up if you can this is a very difficult test. I am not sure where I can study now since the OCG does not come out until March 2016, any help or ideas are appreciated I want to try and pass by 1/8 my cert expires 1/10 and I dont want to have to retake all 4 of the new CCNP Collaboration exams.
ShOuKa
January 3rd, 2016
@ Fitz , Thanks a lot for your feedback
I am waiting for a confirmation on a valid dump so i can enter the exam as currently i cannot afford to fail the exam
Fitz
January 4th, 2016
Let me know what anyone finds, I scheduled my test again on January 8th if I fail again, my cert will expire and I will have to retake the CCNA Collaboration as well as the other 4 CCNP Collaboration exams. There does not seem to be a valid dump out right now that has all of the questions, only about 10 questions or so out of the 52 questions are on the actual exam I took on 12/31. The passing score is 860 so everyone knows but it could be different is some other locations.
Any feedback would be greatly appreciated !!!
Michael
January 5th, 2016
@Fitz Could you send me your email address?
ShOuKa
January 5th, 2016
@Michael , Please share to us valid dumps if you have any
thanks in advance for assistance
Fitz
January 6th, 2016
I can send you the 277q .pdf from passleader.com and it is helpful but maybe 10-15 questions max were on the exam, this .pdf is updated as of 12/31 and I took the exam on 12/31 and failed. Passleader might not have anything else out for weeks, unfortunately my cert expires 1/10 so I cant wait but if you can wait maybe until the end of the month schedule it then.
I would study all of the exam material on the Cisco Learning Network here is the link
Its pretty accurate, alot of VCS Control and Expressway, SAF, CCD, RSVP, CAC, Regions Locations, Device pools. Setup and understand SRST with MGCP, H.323 and SIP, also how SRST works with CME. Some QOS and Service Parameters questions, Device Mobility questions.
Its hard to study for though without an Official Cert Guide thats how I passed all my other tests, I had a guide to study, for this you have to study random guides on the Cisco website.
860 was a passing score for me so the bar is set a little higher as well, only 52 questions 75 min to pass.
I will send you the .pdf
Good luck regardless but reschedule if you can!
Fcochera
January 6th, 2016
@Fitz
Good luck with your exam man !! hope seriously you can pass it. We will wait for your feedback and thoughts on the exam questions.
Could you please send me the passleader pdf so I can review it in the meanwhile? fcochera85@hotmail.com
thank you and best of luck !!!
Fitz
January 6th, 2016
Thanks Fcochera, I will send you the .pdf now
Thanks
NJagga
January 6th, 2016
Can anyone please share pdf for 300-075 to my email njagga@ymail.com. highly appreciated! and good luck to those who are appearing soon…
Colin
January 7th, 2016
Thanks Fitz.
I’ll take a look at the links you have.
Look forward to seeing what questions are on the passleader .pdf have you sent it?
What is the story with Passleader? So do you get to download any updates for like a year?
ShOuKa
January 7th, 2016
@Fitz, please update us back when you take your exam and hope the best for you
Also can you please send to me the 277Q pdf to my mail shouk_1987@hotmail.com
Fitz
January 8th, 2016
@B-Nasty, ShOuka and Techicall, I will send you guys the.pdf now, only 10-15 questions from this dump were on the actual exam out of 52 questions.
I take mine tomorrow so I am hoping I pass but not sure !
Good luck to everyone !!
ShOuKa
January 8th, 2016
@Fitz
I have recieved the file , Thanks a lot
Please tell us how you did today and what questions came to you
Hope the best for you dude
ShOuKa
January 10th, 2016
@Fitz
Please enlighten us here and advise back how was your last exam
Hope the best for you
Michael
January 11th, 2016
Anyone has the latest actualtests 180Q? Please share to me at eyu_999@163.com Thanks a lot
ShOuKa
January 11th, 2016
@MICHAEL, What is this 180Q dump ?
is this a valid one for the current exam ?
Michael
January 11th, 2016
@ShOuKa I don’t know if that is valid or not I just see some guys said they got the new 180Q.
ShOuKa
January 11th, 2016
@Michael, Thanks for your reply
We need to know the correct latest valid dump as i want to enter this exam very soon
riza
January 11th, 2016
Chiming in here. Fitz I hope you passed your test.
Fitz
January 12th, 2016
Hi Everyone, unfortunately I failed again 770 passing score is 860, in desperation I downloaded a test passport exam guide with 180Q it does have some new questions on it but maybe 4, between that guide and the passleader 277q guide only 15 questions were on the 52 question Cisco Exam, this sucks because now I need to pass all 4 exams to earn my CCNP Collaboration now that my CCNP Voice cert is expired. The questions on the exam were alot about SRST, SAF, CAC, RSVP, Locations and regions, VCS Control and Expressway with SIP trunks and search rules and traversal zones. Also how to implement CCD with SAF, some ILS questions, understand how to implement SRST on a SIP ,H323,MGCP Gateway and with CME, one drag and drop question all multiple choice questions, those stupid simlets questions on the exam guides with the scenarios all of those are on those but they are very unclear to read the diagrams.
Study if you can on this, I will send when I can the test passport and the passleader exam guide .pdf files to those who need them but there are only a few new questions on the test passport .pdf.
Good luck to those taking this exam, for me it was very hard, and I have been working with Cisco Voice for about 5 years, I only studied for this exam for about 3 weeks though and there is no OCG to study from, it does not come out until the end of March, so most of the material you have to get from the Cisco Learning Network.
Thos of you who have emailed me I will send you those guides.
Again study what you can, having access to a router a few phones and CUCM is really helpful, actually configuring some of these features such as CCD,SAF , ILS SRST is the best way to learn, hands on at least for me because I am not the best test taker unless I have actually encountered a scenario, just knowing the answers to questions is not the easiest with this stuff because of the broad range of material. Follow the links I posted in a comment above and follow that blueprint on the learning network.
Good Luck again 🙂
NJagga
January 12th, 2016
Hi Fitz,
can you please send the test passport 180q to my email njagga@ymail.com. I will highly appreciate it as I have to renew my CCNP voice before 16th or else pass all exams.
thanks and good luck!
NJ
ShOuKa
January 12th, 2016
@Fitz , I am so sorry for your loss and hope the best for you in the near future
so to conclude the situatuin here, There is currently no certain/confirmed valid dumps for now such that i can enter the exam without hesitation 🙂 ?
Collab
January 12th, 2016
How long we have to wait?
Collab
January 12th, 2016
I think exam was changed on 1st week of Dec and it is over a month now. It is sad that we don’t have the correct ones 🙁
Collab
January 12th, 2016
Actualtest 180Q dump is just copy paste from some old version of exam. So please don’t use that one.
Collab
January 13th, 2016
Guys, As I mentioned in my previous comment, There is no point in using 180Q.
Michael
January 13th, 2016
@Fitz Could you help to download the latest passleader dump ? I see in the web site the latest update is on Jan 12. I will take the exam next Monday so i really need your help. Thanks again. Please send it to my email: eyu_999@163.com
ShOuKa
January 13th, 2016
It would be great if anyone shared the latest passleader dump as they say in their site that the latest dump was updated on 12-Jan
I see a lot of people ask to send to them the latest dump
BUT i see that this is not the correct question to ask !
The correct one is that if there is a valid dump or not ?
Cause i see that all the people entered the exam since start of 2016 are failing , so what benefit will you gain from getting a dump that will probably make you fail the exam !!
Collab
January 16th, 2016
@ShOuKa – Well said. People are failing since beginning of December 2015. Its been over a month that we don’t have any valid dump for this exam. Really not sure how long we have to wait for this!!
Nawaf Khalife
January 18th, 2016
Took my 300-075 exam yesterday! Luckily passed with 920 points (the passing score is 860/1000 now)!
Got 52 questions in total, questions were mainly on SRST, SAF, CAC, RSVP and etc. ….got only ONE drag and drop question and others were MCQs.
Some new questions were available in the premium 300-075 dumps (For me, I learned the premium dumps from: https://tr.im/FCS1t) now!
At last, the most important thing is: studying all objects from Cisco official study guide carefully in case of the NEW questions!!! Good Luck!
Collab
January 18th, 2016
@Nawaf – Link https://tr.im/FCS1t you have provided is taking to passleader. Is this trap to buy the dump and make us fail again?
ShOuKa
January 18th, 2016
@Nawaf , This link is for the passleader dump which for the paid version through the official site
Do you mean that you have bought it and entered the exam after studying it ?
or do you have this version from someone else, if this is the case please share it with us
Michael
January 18th, 2016
Take my 300-075 exam today and very lucky passed with 860. I was prepared it with Passleader 277Q and Actualtests 180Q. But only 10-15 questions are come from their. If you want to pass the exam you also need to study all the topics on the guidelines or waiting the 100% valid dump to release. The new questions not included in 277Q and 180Q i remeber are about ISDN H320 video gateway, CUCM early offer, best network condition for video(packet loss/delay/rount-trip) and mainly on SRST, SAF,CAC, expressway and control, RSVP and etc. Good luck to all
James
January 18th, 2016
@Michael, Congrats. Please could you share the study material you have used?
M@ne
January 18th, 2016
Hello Michael!
Congratulations!
Would you mind sharing the study materials that you used?
it definitely combines questions from 114q and 180q dumps, but seems like it has more.
dimka2000
January 20th, 2016
hmm, someone at the other site did comment that “The Passleader 146 is not valid many new questions on exam. Advise anyone to wait for new questions before booking” 🙁
ShOuKa
January 21st, 2016
Guys, we want to know if there is a valid dump for the current exam or not
I need to enter the exam and schedule for a test but i need to make sure if there is a valid dump or not
There was the 114Q and 277Q then a new 180Q then the newest 180Q
Are all of them invalid or what is our next action here
I also found a new 96q dump on wxam collection that was released 13 jan but has a comment that it is invalid and someone failed using it
@michael @fitz could you please send the file?? iecollab@outlook.com
Does anyone pass recently? Any, updates?
Thanks
James
January 23rd, 2016
Guys,
Below was the question came for 300-075.
Configuration on CME provided like below
On Router 10.0.0.1
Router(config)# telephony-service
Router(config-telephony)# ip source-address 10.0.0.1 port 2000 secondary 10.5.2.78
On Router 10.5.2.78
Router(config)# telephony-service
Router(config-telephony)# ip source-address 10.5.2.78 port 2000 secondary 10.0.0.1
As per above configuration which statement is true
A) HSRP
B) Failover
C) CME redundancy
D) CME standby
Anyone can suggest correct answer here? Is the Answer is “Failover”
Cheers,
Like this I have noted many questions, If you guys can share the answer I am happy to post more questions here 🙂
ShOuKa
January 24th, 2016
I think it is failover correct but not sure actually
James,
please, post all the questions you remember.
Farhan
January 26th, 2016
can Anyone Answer this Question.
What roles do you use to move and domain naming server and infrastructure master.
Infrastructure master
Domain naming Server
Which belong to which one
AD domain and Site
Security Configuration Wizard
AD computer and user
Domain Schema
Domain Trust
ShOuKa
January 26th, 2016
@pml , can you please share this 239q
Note that as far as i know, there is no dump that has questions for video ( not 42 !! )
My mail is shouk_1987@hotmail.com
I guess @fitz can assist you as he entered the exam very recently
sUNNY
January 27th, 2016
Hey all
is : Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) 114 Questions & Answers from actual test is valid ? pls share if any one have recently given this exam.
Has anybody password today 300-075 using 114Q dumps? please confirm…………I want to give the exam this week.
Thanks
Hi guys,
Passed today with 979, 114Q still valid!!!
Thanks! 🙂
Hi
114Q for the 300-075 exam is still valid.
Passed today.
peoples you should download latest dumps from this link
” tiny. cc/9tut “
Hi,
any update info ?? is 114Q still valid??
Please Info ??
is 114Q still valid??
Hello Assem!
Based on this comment:
http://www.examcollection.com/cisco/Cisco.Testking.300-075.v2015-07-28.by.Larry.44q.vce.file.html
Looks like it is still valid….
Dear All
114Q for the 300-075 exam is still valid.
Passed today with 969/1000
New 300-070 Exam Questions and Answers Updated Recently:
NEW QUESTION 72
What are the two benefits of using SIP dial rules on an IP phone? (Choose two)
A. The phone can initiate dialing without sending any signaling messages to Cisco Unified CommunicationsManager.
B. The phone can detect invalid numbers and play a reorder tone without sending any signaling messages toCisco Unified Communications Manager.
C. If dialed digits match an entry of a SIP dial rule, the dialed string is sent in a single SIP 200 OK message toCisco Unified Communications Manager.
D. If Cisco Unified Communications Manager requires more digits, KPML can be used to send the remainingdigits from the SIP phone to Cisco Unified Communications Manager one-by-one.
E. If Cisco Unified Communications Manager requires more digits, another en bloc message is used to sendthe remaining digits from the SIP.
Answer: BD
NEW QUESTION 73
Which three Cisco Unified CallManager configuration steps are required to support third party SIP phones? (Choose three.)
A. Configure the device in Cisco Unified CallManager.
B. Change the proxy address in the SIP phone to an IP address or the Fully Qualified Domain Name (FQDN)of Cisco Unified CallManager.
C. Associate the device with the end user.
D. Configure the phone with the TLS username and password.
E. Configure the end user in Cisco Unified CallManager.
F. Add the MAC address of the Cisco Unified CallManager server to the SIP phone configuration page.
Answer: ACE
NEW QUESTION 74
Which four software based media resources require that the Cisco IP voice media stream Application be activated?
A. MOH.
B. SIP.
C. H.323 Gateways.
D. Annunciator.
E. Gatekeeper.
F. MTP.
G. Audio conferencing.
Answer: ADFG
NEW QUESTION 75
Which protocol is recommended to be used between Cisco Unified Communications Manager and the voice gateway to simplify the dial plan?
A. SIP.
B. SCCP.
C. H323.
D. RSVP.
E. MGCP.
Answer: E
NEW QUESTION 76
Which protocol can Cisco Unified Communications Manager not use to monitor the status of the gateway?
A. H.323
B. SIP
C. MGCP
D. SCCP
Answer: A
NEW QUESTION 77
In a centralized call-processing solution, there are five sites connected through an IP WAN. To optimize the utilization of the IP WAN, CAC needs to be implemented. How should CAC be implemented?
A. Use a gatekeeper to control allocated bandwidth properly.
B. Use locations CAC with a single location.
C. Use a gatekeeper and Cisco Unified Border Element to provide CAC to sites that use a combination of SIPand MGCP gateways.
D. Use a gatekeeper to only control those locations that use H.323 gateways and a Cisco Unified BorderElement to control those sites that use MGCP or SIP gateways.
E. Use locations CAC with five locations in addition to Hub none.
Answer: E
NEW QUESTION 78
Which two features are advantages of deploying a cluster over WAN? (Choose two.)
A. Shared line appearances
B. CentralizedDSP resources
C. Extension mobility within the cluster
D. Scalability up to 20 sites, if thereis sufficient IP WAN bandwidth
E. Failover to co-resident Cisco UnifiedCall Manager Express platforms
Answer: AC
NEW QUESTION 79
The Ajax Corporation is designing an IP telephony network using Cisco MCS 7845 Series servers, each one capable of supporting 7500 devices. The design must meet these requirements:
– Be cost-effective
– Support up to 7500 phones
– Provide a minimal level of redundancy
Which configuration will meet Ajax Corporation needs?
A. Two Cisco Unified Communications Manager servers:
1 publisher and TFTP server combined.
1 primary subscriber.
B. Three Cisco Unified Communications Manager servers:
1 publisher and TFTP server combined.
1 primary subscriber.
1 backup subscriber.
C. Four Cisco Unified Communications Manager servers:
1 publisher.
1 TFTP server.
1 primary subscriber.
1 backup subscriber.
D. Five Cisco Unified Communications Manager servers:
1 publisher.
1 TFTP server.
1 primary subscriber.
2 backup subscribers.
Answer: B
NEW QUESTION 80
How are Cisco Unified CallManager location parameters used?
A. Assign directory numbers to devices as they connect to the IP telephony network.
B. Specify the bandwidth used for audio and video calls.
C. Implement call admission control in a centralized call processing deployment.
D. Provide alternate call routing when the primary call path is unavailable.
Answer: C
NEW QUESTION 81
Which statement regarding Cisco IP voice media streaming application is correct?
A. It should be activated on the gateway in cluster that supports the TFTP service.
B. It should be activated on the gatekeeper in cluster that supports the TFTP service.
C. It should be activated on the node in cluster that does not support the TFTP service.
D. It should be activated on the node in cluster that supports the TFTP service.
Answer: D
NEW QUESTION 82
Which option describes how you add software conference bridges to Cisco Unified Communications Manager?
A. By adding a Cisco Unified CM server to the cluster.
B. By adding a software conference bridge using Conference Bridge Configuration.
C. By installing DSP to a Cisco Unified CM server.
D. By reassigning other media resources to conference resources.
Answer: A
NEW QUESTION 83
Which of these media resources can be configured in Cisco Unified Communication manager? (Choose Three)
A. MOH Server
B. Voice Termination Point DSP
C. Transcoder
D. Auto Attendant
E. Conference Bridge
Answer: ACE
NEW QUESTION 84
What is the relationship between a Region and a Location?
A. The Region codec parameter is used between a Region and its configured Locations.
B. The Region setting for a Location sets the number of audio and video calls that Location can support.
C. The codec parameter configured in the Region is only used between Regions and Location bandwidth isonly used between Locations.
D. The Region codec parameter is combined with Location bandwidth when communicating with otherRegions.
Answer: C
NEW QUESTION 85
……
BTW, These New 300-070 Exam Questions Were Updated By PassLeader, You Can Get The Newest 300-070 Dumps In PDF And VCE From — http://www.passleader.com/300-070.html
Good Luck !!!
New 300-085 Exam Questions and Answers Updated Recently:
NEW QUESTION 61
Which CCC action applies only to the Cisco TelePresence MPS Series?
A. block fast update requests
B. Status Duo Video
C. move back
D. release floor
Answer: A
NEW QUESTION 62
Which protocol is prioritized by Cisco TMS for conferencing?
A. SIP
B. MGCP
C. H.323
D. SCCP
Answer: C
NEW QUESTION 63
How does Cisco TMS set up a call with an endpoint that is registered with Cisco Unified Communications Manager and that is connected to Cisco VCS?
A. Cisco TMS uses an IP dialing plan.
B. Cisco TMS uses a SIP trunk.
C. Cisco TMS removes the top-level domain from calls that go through Cisco Unified Communications Manager.
D. Cisco TMS drops the call, because it can verify that the trunk between Cisco Unified Communications Manager and Cisco VCS is down.
Answer: B
NEW QUESTION 64
On Cisco TelePresence Management Suite, which two call control devices are supported for call control and setup? (Choose two.)
A. Cisco Unified Communications Manager Express
B. Cisco TelePresence Video Communication Server
C. Cisco Unified Border Element
D. Cisco Unified Communications Manager
E. any SIP-capable call control system
Answer: BD
NEW QUESTION 65
Which three are valid system connectivity statuses for systems that are automatically added to Cisco TelePresence Management Suite? (Choose three.)
A. Inaccessible
B. Failed
C. Connected
D. Reachable on Public Internet
E. Behind Firewall
F. Online
G. Remote Site
Answer: ADE
NEW QUESTION 66
To have a Provisioning menu section available on Cisco TelePresence Management Suite, what must you do?
A. You must configure an active ISDN zone.
B. You must install Cisco TelePresence Management Suite Provisioning Extension and activate it on the system.
C. You must license Cisco TelePresence Management Suite Analytics Extension.
D. You must set up Cisco TelePresence deployment to support Cisco CMR Hybrid.
Answer: B
NEW QUESTION 67
Which two actions must you take to enable provisioning on Cisco TMS and Cisco VCS? (Choose two.)
A. Apply a Device Provisioning option key on Cisco VCS.
B. Enable provisioning on Cisco VCS under Applications > Provisioning.
C. Configure Users, FindMe, Phonebooks, and Devices individually, as these all have different settings.
D. Configure a separate server to run provisioning extension services.
E. Ensure that a service account is able to connect.
F. Set the polling intervals on Users, FindMe, Phonebooks, and Devices to the same value, in order for the synchronization to work.
Answer: AE
NEW QUESTION 68
What must you do to activate the provisioning feature on a Cisco VCS endpoint?
A. Install the Device Provisioning option key.
B. Set a SIP trunk between Cisco VCS and Cisco Unified Communications Manager.
C. Add the Cisco VCS on the Cisco TMS, and enable Cisco Extension Mobility.
D. Install Cisco VCS Starter Pack Express.
Answer: A
NEW QUESTION 69
Refer to the exhibit. Which statement about the jabber-config.xml partial output is true?
A. 10.255.10.10 is the LDAP server address.
B. The client connects to the directory server by using SSH.
C. 10.255.10.10 is the Cisco Unified Communications Manager IM and Presence Service address.
D. The client connects to the directory server by using HTTPS.
Answer: D
NEW QUESTION 70
The UDS for contact resolution is enabled in the service profile configuration of the Cisco Unified Communications Manager. Which action can you execute with your Jabber Desktop?
A. modify users
B. search users
C. change users
D. delete users
Answer: B
NEW QUESTION 71
Which profile must you add to an end user record, if the end user wants to access voicemail and wants to control a deskphone via CTI with Cisco Jabber?
A. remote destination profile
B. device profile
C. SIP profile
D. service profile
E. phone service
Answer: D
NEW QUESTION 72
……
BTW, These New 300-085 Exam Questions Were Updated By PassLeader, You Can Get The Newest 300-085 Dumps In PDF And VCE From — http://www.passleader.com/300-085.html
Good Luck !!!
New 300-080 Exam Questions and Answers Updated Recently:
NEW QUESTION 76
Phone A is able to dial the directory number of Phone B and complete a call. However, when Phone B dials the directory number of Phone A, Phone B receives a fast-busy tone. What is causing this issue?
A. Phone A and Phone B are in different partitions.
B. Phone B does not have Phone A in its partition.
C. Phone B is not in the CSS of Phone A.
D. Phone B does not have the CSS of Phone A in its partition.
E. Phone B is not registered.
F. Phone B has the incorrect CSS to dial Phone A.
Answer: F
NEW QUESTION 77
An inbound call from the PSTN is not reaching the directory number that it is calling. When the PSTN phone calls the correct DID, only a dial tone is heard. Which command resolves this issue?
A. (config-dial-peer)#direct-inward-dial
B. (config-controller)# no provide-outside-dialtone
C. (config-if)#no dial-tone
D. (config-dial-peer)# no dial-tone
E. (config-if)#direct-inward-dial
F. (config) allow inbound dial-peer 1
Answer: A
NEW QUESTION 78
When a caller dials 9 plus an external seven-digit number, the caller hears a fast-busy tone after a period of silence. What is causing the silence?
A. There is no dial route for 9XXXXXXX on Cisco Unified Communications Manager.
B. The gateway is not dropping the leading 9, and the PSTN fails.
C. The T302 timer is waiting to expire.
D. The caller does not have the PSTN partition in the CSS.
E. The caller dialed the wrong number.
F. To dial successfully, the caller must enter a Forced Authorization Code.
Answer: C
NEW QUESTION 79
In a single-site deployment model, the internal endpoints are unable to dial from one to the other. What are two possible causes? (Choose two.)
A. The PSTN gateway is not configured.
B. The called endpoint does not have the SIP trunk enabled.
C. The called endpoint is not registered.
D. The calling endpoint is not in the CSS of the called endpoint.
E. The called endpoint is not in the partition of the calling endpoint.
F. The calling endpoint is not configured for the correct CoS.
Answer: CF
NEW QUESTION 80
What is the default interval for SAF hello packets?
A. 15 seconds
B. 15 seconds on links with speeds that are slower than T1 speeds
C. 40 seconds
D. 40 seconds onlinks with speeds that are slower than T1 speeds
E. 60 seconds
F. 60 seconds onlinks with speeds that are slower than T1 speeds
Answer: F
NEW QUESTION 81
Which configuration can be dynamically set using the Cisco Unified Communications Manager Device Mobility feature?
A. phone model and protocol
B. SRST reference and directory number
C. CSS and local gateway
D. partition and CSS
E. media resources and permanent bridges
Answer: C
NEW QUESTION 82
Which configuration is required on Cisco TelePresence Server, in order to support 1080p resolution?
A. Screen licenses must be configured.
B. Cisco TelePresence Server must be in remotely managed mode.
C. Cisco TelePresence Server must be in HD mode.
D. Cisco TelePresence Server must be configured with Cisco TelePresence Conductor.
E. Cisco TelePresence Server must be in Full HD mode.
Answer: E
NEW QUESTION 83
A user is dialing an external PSTN number with a prefix of 01 from a Cisco TelePresence SX10 Quick Set in a Cisco VCS environment. In the past, the Cisco VCS and the ISDN gateway were correctly configured with a prefix of 01, but the calls are now failing. What are three possible causes? (Choose three.)
A. The Cisco VCS Control is down.
B. The interworking setting is turned off.
C. The audio feature in the Cisco TelePresenceSX10 is turned off.
D. The SIP trunk is not configured on the gateway.
E. 01 is not a valid prefix.
F. ISDN is not enabled on the Cisco TelePresenceSX10.
G. The Cisco TelePresenceSX10 is not registered to the Cisco VCS Control.
H. The Cisco TelePresenceSX10 is not registered to the Cisco Express C.
Answer: ABG
NEW QUESTION 84
When the command utils dbreplication status is executed on the Cisco Unified Communications Manager CLI, which step should be taken next to check the database replication status?
A. View the activelog file.
B. Run the same command on all nodes of the cluster.
C. Restart the Cisco CallManager service.
D. The command utils dbreplication runtimestate must be run on the publisher.
E. The command utils dbreplication runtimestate must be run on the subscriber.
Answer: A
NEW QUESTION 85
Which tool can you use to see SAF advertisements in Cisco Unified Communications Manager?
A. Cisco Unified Real-Time Monitoring Tool
B. show eigrp neighbors command
C. debug eigrp commands
D. Terminal Monitor
Answer: A
NEW QUESTION 86
URI dialing is enabled between two clusters with the default options. The engineer that set up the URI dialing verified that all was working properly. However, a user from one of the clusters cannot dial using URI to a user in the same cluster. What do you do to resolve this issue?
A. Verify the password that is used by the authentication under Intercluster Lookup Service configuration.
B. Find out if the URI address of the called user has a capital letter in the URI string.
C. Verify that Intercluster Lookup Service is set up correctly.
D. Verify USN Data Synchronization Status.
Answer: B
NEW QUESTION 87
……
And, These New 300-080 Exam Questions Were Updated By PassLeader, You Can Get The Newest 300-080 Dumps In PDF And VCE From — http://www.passleader.com/300-080.html
Good Luck !!!
Hello Everyone!
Has it updated?
Has anyone cleared the 300-075 exam in the last 2 days, want to ensure if dumps have changed or not!
Yes… 114Q was valid.
Any Updates?
Hi ,all
I attend the exam 300-075 and actual test 114 Q is still valid thank you for any one who shared the pdf file .
Scored 9XX/1000
All question is from the dump
the passing score is 860
To whom would like to download the bundle that i gathered :
114 PDF +VCE converted from pdf + Vce+its crack
Download it from the below link
http://www.4shared.com/get/44oGiMzjce/300-075_Exam_Bundles.html
the password for the rar file is
monsour
for the new question
Which protocol can Cisco Unified Communications Manager not use to monitor the status of the gateway?
A. H.323
B. SIP
C. MGCP
D. SCCP
Where is the Answer: A documented?
I will be taking mine before year end – thX !
Hello Everyone!
Are there new questions on exam?
what are the new questions in the exam that are not in the dump?
@Mansour:
Thanks for the VCE. I’ve worked through a little over 1/3 of it looking up each answer and filling in the Explanation and Reference. I’ve found some mistakes:
Your Question 2 should be A instead of B (Same as in Actualtests which has A) per Cisco TelePresence Video Communication Server Administrator Guide (X8.5.1) Page 474 of 563.
I think question 40 is wrong (both Actualtests and VCE). I cannot find any references to multiple autonomous systems in the Cisco docs, but I do find reference that the client label in CUCM must match what’s on the SAF router. Cisco Unified Communications Manager Features and Services Guide, Release 9.1(1) Page 80.
Can anyone confirm or deny question 40???
Also regarding question 40, The same doc says:
Autonomous System
All Cisco Unified Communications Manager clusters are limited to advertised or learned routes within the same autonomous system (AS).
Hello Guys, anyone knows if the actualtest 114Q is still valid? Please Help!, I’m gonna take the exam next monday.
I think this does the trick:
http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/service-advertisement-framework-saf/whitepaper_c11-622512.html
I uploaded a complete VCE to examcollect using the actual + Q72-84 from here but is has not shown up yet
colleague and i took and failed the 300-075 yesterday. 781 for myself 708 for him. We both knew the 114Q inside and out. Saw many SAF questions, port for mgcp and MTP questions (which i actually found answers to on the CCIE Collab MTP video from INE)
hello guys
I lost my exam, there are many new questions
Hello Friends I just gave my exam and failed with 750 score passing score was 860 with 75 Minutes to finish this exam. I did preparation from Actualtest 114Q and PassLeader 146Q only 10 to 15 questions came from them all new question. Don’t book your exam until you have correct answers otherwise its waste of Money Thanks
Hello, is the 114q dump still valid?
Anonymous
Can you describre a little about these new questons?
Thank You.
lot’s of SAF, MTP questions (that i’ve seen in CCIE Collab INE Videos), typos, grammar issues.. All in all, this revamp was very poorly done. it was 52 questions instead of 60 though. i had 12 from the 114Q, everything else was new.
Hi All,
Have you refered the brain dumps questions from
http://s000.tinyupload.com/?file_id=19647777086643018828 (which was forwarded from Kink earlier) as it has very questions which are not there in 114 questions which was forwarded by Nina and Mansour…
The ones who have given the exam recently last week…can you please let me know whether the brain dump is Ok.?.because i need to give the exam be fore dec 31st …
@Abhijeet no the dump by Kink is not including the new questions in the exam – reschedule your exam or you will lose your money
@Abhijeet i also just looked through your dump and i didnt see anything on it that wasn’t already on the 114Q. suggest you take a different CCNP exam to renew.
Are we sure that http://s000.tinyupload.com/?file_id=19647777086643018828 is still available?
Hello Everyone!
Theses are no longer valid!
Wait for the updates.
Did my exam on 15th and it is not valid. Used the 114q file.
Hello guys
Are there valid dumps now ?
cause from the comments, it seems that 114Q dump is no longer valid
Please hsare to us the valid dumps if there are any
Hi,
can anyone share the valid dumps to sherio123@hotmail.com
Passleader support is claiming to have a new version out tomorrow of the 300-075 if that is true I will download the PDF and send it to whoever needs it, it states their current version with 146Q is updated as of 12/22 but that cant be true as the last modified date of the .vce and .pdf file once you download it states 10/5. My exam is tomorrow so hopefully I can study some of the new version if its released before the test, I am not big on dumps, but there is no OCG on this exam, it does not release until March 2016 so I dont get how Cisco came out with a new exam in October? Plus my CCNP Voice expires 1/10/16 so I need to pass now.
Well I got the passleader.com 300-075 guide with 277Q it was supposed to be updated and it definitely is, its more updated than anything else I have, but I memorized all 277Q before my exam today and only 10 or 15 questions were on the exam. I am not sure where to get any more training material, I got a 759 and failed, you need a 860 to pass. Most of the questions I got right I knew from on the job experience, others were a guess, I studied some materia of of Cisco Learning Network but there is not much on there for this. There were alot of questions about SAF, ILS, CAC,SRST,RSVP Bandwidth and Region questions, VCS Control and VCS Expressway ad Device Mobility questions as well, Study up if you can this is a very difficult test. I am not sure where I can study now since the OCG does not come out until March 2016, any help or ideas are appreciated I want to try and pass by 1/8 my cert expires 1/10 and I dont want to have to retake all 4 of the new CCNP Collaboration exams.
@ Fitz , Thanks a lot for your feedback
I am waiting for a confirmation on a valid dump so i can enter the exam as currently i cannot afford to fail the exam
Let me know what anyone finds, I scheduled my test again on January 8th if I fail again, my cert will expire and I will have to retake the CCNA Collaboration as well as the other 4 CCNP Collaboration exams. There does not seem to be a valid dump out right now that has all of the questions, only about 10 questions or so out of the 52 questions are on the actual exam I took on 12/31. The passing score is 860 so everyone knows but it could be different is some other locations.
Any feedback would be greatly appreciated !!!
@Fitz Could you send me your email address?
@Michael , Please share to us valid dumps if you have any
thanks in advance for assistance
I can send you the 277q .pdf from passleader.com and it is helpful but maybe 10-15 questions max were on the exam, this .pdf is updated as of 12/31 and I took the exam on 12/31 and failed. Passleader might not have anything else out for weeks, unfortunately my cert expires 1/10 so I cant wait but if you can wait maybe until the end of the month schedule it then.
I would study all of the exam material on the Cisco Learning Network here is the link
https://learningnetwork.cisco.com/community/certifications/ccnp-collaboration/ciptv2-exam/study-material
Then follow the exam material outline so you know what to expect
Thats here
https://learningcontent.cisco.com/cln_storage/text/cln/marketing/exam-topics/300-075-ciptv2.pdf
Its pretty accurate, alot of VCS Control and Expressway, SAF, CCD, RSVP, CAC, Regions Locations, Device pools. Setup and understand SRST with MGCP, H.323 and SIP, also how SRST works with CME. Some QOS and Service Parameters questions, Device Mobility questions.
Its hard to study for though without an Official Cert Guide thats how I passed all my other tests, I had a guide to study, for this you have to study random guides on the Cisco website.
860 was a passing score for me so the bar is set a little higher as well, only 52 questions 75 min to pass.
I will send you the .pdf
Good luck regardless but reschedule if you can!
@Fitz
Good luck with your exam man !! hope seriously you can pass it. We will wait for your feedback and thoughts on the exam questions.
Could you please send me the passleader pdf so I can review it in the meanwhile?
fcochera85@hotmail.com
thank you and best of luck !!!
Thanks Fcochera, I will send you the .pdf now
Thanks
Can anyone please share pdf for 300-075 to my email njagga@ymail.com. highly appreciated! and good luck to those who are appearing soon…
Thanks Fitz.
I’ll take a look at the links you have.
Look forward to seeing what questions are on the passleader .pdf have you sent it?
What is the story with Passleader? So do you get to download any updates for like a year?
@Fitz, please update us back when you take your exam and hope the best for you
Also can you please send to me the 277Q pdf to my mail
shouk_1987@hotmail.com
@B-Nasty, ShOuka and Techicall, I will send you guys the.pdf now, only 10-15 questions from this dump were on the actual exam out of 52 questions.
I take mine tomorrow so I am hoping I pass but not sure !
Good luck to everyone !!
@Fitz
I have recieved the file , Thanks a lot
Please tell us how you did today and what questions came to you
Hope the best for you dude
@Fitz
Please enlighten us here and advise back how was your last exam
Hope the best for you
Anyone has the latest actualtests 180Q? Please share to me at eyu_999@163.com Thanks a lot
@MICHAEL, What is this 180Q dump ?
is this a valid one for the current exam ?
@ShOuKa I don’t know if that is valid or not I just see some guys said they got the new 180Q.
@Michael, Thanks for your reply
We need to know the correct latest valid dump as i want to enter this exam very soon
Chiming in here. Fitz I hope you passed your test.
Hi Everyone, unfortunately I failed again 770 passing score is 860, in desperation I downloaded a test passport exam guide with 180Q it does have some new questions on it but maybe 4, between that guide and the passleader 277q guide only 15 questions were on the 52 question Cisco Exam, this sucks because now I need to pass all 4 exams to earn my CCNP Collaboration now that my CCNP Voice cert is expired. The questions on the exam were alot about SRST, SAF, CAC, RSVP, Locations and regions, VCS Control and Expressway with SIP trunks and search rules and traversal zones. Also how to implement CCD with SAF, some ILS questions, understand how to implement SRST on a SIP ,H323,MGCP Gateway and with CME, one drag and drop question all multiple choice questions, those stupid simlets questions on the exam guides with the scenarios all of those are on those but they are very unclear to read the diagrams.
Study if you can on this, I will send when I can the test passport and the passleader exam guide .pdf files to those who need them but there are only a few new questions on the test passport .pdf.
Good luck to those taking this exam, for me it was very hard, and I have been working with Cisco Voice for about 5 years, I only studied for this exam for about 3 weeks though and there is no OCG to study from, it does not come out until the end of March, so most of the material you have to get from the Cisco Learning Network.
Thos of you who have emailed me I will send you those guides.
Again study what you can, having access to a router a few phones and CUCM is really helpful, actually configuring some of these features such as CCD,SAF , ILS SRST is the best way to learn, hands on at least for me because I am not the best test taker unless I have actually encountered a scenario, just knowing the answers to questions is not the easiest with this stuff because of the broad range of material. Follow the links I posted in a comment above and follow that blueprint on the learning network.
Good Luck again 🙂
Hi Fitz,
can you please send the test passport 180q to my email njagga@ymail.com. I will highly appreciate it as I have to renew my CCNP voice before 16th or else pass all exams.
thanks and good luck!
NJ
@Fitz , I am so sorry for your loss and hope the best for you in the near future
so to conclude the situatuin here, There is currently no certain/confirmed valid dumps for now such that i can enter the exam without hesitation 🙂 ?
How long we have to wait?
I think exam was changed on 1st week of Dec and it is over a month now. It is sad that we don’t have the correct ones 🙁
Actualtest 180Q dump is just copy paste from some old version of exam. So please don’t use that one.
Guys, As I mentioned in my previous comment, There is no point in using 180Q.
@Fitz Could you help to download the latest passleader dump ? I see in the web site the latest update is on Jan 12. I will take the exam next Monday so i really need your help. Thanks again. Please send it to my email: eyu_999@163.com
It would be great if anyone shared the latest passleader dump as they say in their site that the latest dump was updated on 12-Jan
Fitz, please send the updated passleader to me too..njagga@ymail.com
Hi Guys,
anyone have valid dump , plz send it to me on faisal.saoud@hotmail.com
Thanks
Guys
I see a lot of people ask to send to them the latest dump
BUT i see that this is not the correct question to ask !
The correct one is that if there is a valid dump or not ?
Cause i see that all the people entered the exam since start of 2016 are failing , so what benefit will you gain from getting a dump that will probably make you fail the exam !!
@ShOuKa – Well said. People are failing since beginning of December 2015. Its been over a month that we don’t have any valid dump for this exam. Really not sure how long we have to wait for this!!
Took my 300-075 exam yesterday! Luckily passed with 920 points (the passing score is 860/1000 now)!
Got 52 questions in total, questions were mainly on SRST, SAF, CAC, RSVP and etc. ….got only ONE drag and drop question and others were MCQs.
Some new questions were available in the premium 300-075 dumps (For me, I learned the premium dumps from: https://tr.im/FCS1t) now!
At last, the most important thing is: studying all objects from Cisco official study guide carefully in case of the NEW questions!!! Good Luck!
@Nawaf – Link https://tr.im/FCS1t you have provided is taking to passleader. Is this trap to buy the dump and make us fail again?
@Nawaf , This link is for the passleader dump which for the paid version through the official site
Do you mean that you have bought it and entered the exam after studying it ?
or do you have this version from someone else, if this is the case please share it with us
Take my 300-075 exam today and very lucky passed with 860. I was prepared it with Passleader 277Q and Actualtests 180Q. But only 10-15 questions are come from their. If you want to pass the exam you also need to study all the topics on the guidelines or waiting the 100% valid dump to release. The new questions not included in 277Q and 180Q i remeber are about ISDN H320 video gateway, CUCM early offer, best network condition for video(packet loss/delay/rount-trip) and mainly on SRST, SAF,CAC, expressway and control, RSVP and etc. Good luck to all
@Michael, Congrats. Please could you share the study material you have used?
Hello Michael!
Congratulations!
Would you mind sharing the study materials that you used?
e_avelino@hotmail.com
Thank You.
Same here @Micheal
Please guide us on how or the material that you studied from and thx
I study at SRND 10 and VCS admin gudie 8.6 and also lookin Cisco learningnetwork. https://learningnetwork.cisco.com/community/certifications/ccnp-collaboration/ciptv2-exam/study-material
@M@ne i have send you the 277Q dump where i get the dump from Fitz. Thanks for Fitz sharing it.
One thing regarding the recent comments:
When I look at the 114q dump there are many questions about VCE, SRST, SAF etc.
So are the questions in the exam completly different?
What version?
114q inkl. Sim:
https://www.dropbox.com/s/49nh66pa62zsrd8/vce%20player.zip?dl=0
Maybe this helps also: http://we.tl/ln3DQZIe3U
@Zahackn
Thanks!
It’s valid ?
I checked examcollection,
users talking that new 180q dump is valid, 114q not valid yet.
Anybody got this ?
As far as I know the 180q is the old CIPT 2 one. In this dump there is nothing about video.
Other question does anybody have the drag and drop question of the exam?
hey, can someone who took the test recently, verify this dump?
https://dl-dot-dropboxusercontent-dot-com/u/1824024/300-075.teste_vce.vce (replace -dot- with .)
it definitely combines questions from 114q and 180q dumps, but seems like it has more.
hmm, someone at the other site did comment that “The Passleader 146 is not valid many new questions on exam. Advise anyone to wait for new questions before booking” 🙁
Guys, we want to know if there is a valid dump for the current exam or not
I need to enter the exam and schedule for a test but i need to make sure if there is a valid dump or not
There was the 114Q and 277Q then a new 180Q then the newest 180Q
Are all of them invalid or what is our next action here
I also found a new 96q dump on wxam collection that was released 13 jan but has a comment that it is invalid and someone failed using it
Hi Michael, guys
Please could you share 277Q with us? My email id is edisson.realpe.i@hotmail.com. I need this please.
hi michael !!!
please coud you share 277Q .
jreyes_guzman@hotmail.com
Anybody can share 300-075 ?
277
@michael @fitz could you please send the file?? iecollab@outlook.com
Does anyone pass recently? Any, updates?
Thanks
Guys,
Below was the question came for 300-075.
Configuration on CME provided like below
On Router 10.0.0.1
Router(config)# telephony-service
Router(config-telephony)# ip source-address 10.0.0.1 port 2000 secondary 10.5.2.78
On Router 10.5.2.78
Router(config)# telephony-service
Router(config-telephony)# ip source-address 10.5.2.78 port 2000 secondary 10.0.0.1
As per above configuration which statement is true
A) HSRP
B) Failover
C) CME redundancy
D) CME standby
Anyone can suggest correct answer here? Is the Answer is “Failover”
Cheers,
Like this I have noted many questions, If you guys can share the answer I am happy to post more questions here 🙂
I think it is failover correct but not sure actually
looks like CME redundancy is the correct answer, as this is the lingo Cisco uses in this guide:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmesystm.html
James,
please, post all the questions you remember.
can Anyone Answer this Question.
What roles do you use to move and domain naming server and infrastructure master.
Infrastructure master
Domain naming Server
Which belong to which one
AD domain and Site
Security Configuration Wizard
AD computer and user
Domain Schema
Domain Trust
@pml , can you please share this 239q
Note that as far as i know, there is no dump that has questions for video ( not 42 !! )
My mail is shouk_1987@hotmail.com
I guess @fitz can assist you as he entered the exam very recently
Hey all
is : Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) 114 Questions & Answers from actual test is valid ? pls share if any one have recently given this exam.