Share your CIPT1 v8.0 Experience

In our office our Publisher isn’t the DHCP server. So the answers are A and E.

@Selsius

Going back to my previous question (24th Aug 2011) about the phone restoring connectivity to the primary server, I am still confused after reading below question and its answer.

QUESTION NO: 28
How does an IP phone maintain its connection with the primary and secondary Cisco Unified
Communications Manager servers in the cluster?
A. Cisco IP phones register with their primary server. When idle, the IP phones and Cisco Unified Communications Manager exchange the signaling applicationkeepalives. In addition, Cisco IP phones establish a UDP session with their secondary server and exchange UDP keepalives.
B. Cisco IP phones register with their primary server. When idle, the IP phones and Cisco Unified Communications Manager exchange the signaling applicationkeepalives. In addition, Cisco IP phones establish a TCP session with their secondary server and exchange TCP keepalives.
C. Cisco IP phones register with their primary and secondary servers. When idle, the IP phones
and Cisco Unified Communications Manager exchange the signaling applicationkeepalives with
both servers using UDP keepalives.
D. Cisco IP phones register with their primary and secondary servers. When idle, the IP phones
and Cisco Unified Communications Manager exchange the signaling applicationkeepalives. In
addition, Cisco IP phones establish a TCP session with their secondary server and exchange TCP
keepalives.
Answer: B

There is no doubt B is the answer of above question.

If you notice in option B, it is mentioned IP phones establish a TCP session with their secondary server and exchange TCP keepalives.

I have also searched on google and found that IP phone will wait untill 3 keepalives and then only it will treat that connection as good connection.

So I strongly feel that D is the answer for my previous question date 24th Aug 2011.

What you say? If anyone else have input on this then please share.

Mate,

Check this out from the CIPT1 book:

Cisco IP Phones register with their primary server. When idle, the Cisco IP Phones and
CUCM exchange signaling application keepalives. In addition, Cisco IP Phones establish
a TCP session with their secondary server and exchange TCP keepalives. When the
connection to the primary server is lost (no keepalives received), the Cisco IP Phone
registers to the secondary server. The Cisco IP Phone will continuously try to reestablish
a connection with the primary server; if successful, the Cisco IP Phone will reregister with
the primary server.

Thanks dude.. 🙂

Also I would appriciate if you could share CIPT1 book, I am searching for it but still no success.

Thanks in advance.

I’ve the old book ;-).

Passed with an 895.
I notice that for some of the questions that were in the dump, different answers sometimes appeared on the test.
The only ones I remember…
…For the question about media resources and audio streams there was an answer that said, “audio streams only use RTP or SRTP”
…For the question about dummy MACs in a CSV file they added some ridiculous answer and made the question easier so that now there in only one possible right answer.

On to CIPT 2

@ Selsuis

Congratulations! How would you suggest getting some hands on practice on CUCM and its components? What is the BEST way to learn this course?

Selsius,

Congrats,mate! How was the dump? Valid? And what about the both question that you’ve quoted … which are the answers? The added in the exam or this in the dump?

@SC, the dump is close enough that it is valid for exam prep. There were a few new questions but mostly the ones from the dump. For the media resource one I thought the audio streams use RTP or SRTP was a right answer. For the other one I thought the new answer was bogus. Look through the Dump, it is the question refering to dummy mac addresses I chose the following answer: “The MAC address is left blank in the CSV file and Cisco Unified Communications Manager BAT imports the
CSV file with the Create Dummy MAC Address option selected, ” which is the answer the dump gave.

Thank you. Do u remember any of the new questions?

Can somebody help me with this question?

The abc.com Corporation is experiencing poor, choppy audio quality on voice calls placed across their WAN link to and from Madison. What can be done to the Location parameter for Madison to help alleviate this problem?

A. Nothing, the audio bandwidth Location parameter for Madison is not related to the problem.
B. Increase the audio bandwidth setting in the Location configuration window for Madison.
C. Decrease the audio bandwidth setting in the Location configuration window for Madison.
D. Remove the audio bandwidth parameter in the Location configuration window for Madison.

In the VCE says the answer is C, but I think is A.
This is the only Note that I found:

Use locations to implement CAC…
Note: If CAC is not used to limit the audio and video bandwidth on IP WAN links, an unlimited number of calls can be active on that link at the same time. This situation can cause the quality of all audio and video calls to degrade as the link becomes oversubscribed.

All,

Passed the exam today with 87x points. The most of the question was from the Xenix dump, but keep in mind that there are a lot of different answers.

Good luck!

@Cris
Similar thing is mentioned in CUCM System Guide (Call Admission Control). It says:
“Audio and video quality can begin to degrade when too many active calls exist on a link and the amount of bandwidth is oversubscribed. Call admission control regulates audio and video quality by limiting the number of calls that can be active on a particular link at the same time.”

This means if you are using a 64kbps link, only two g.729 call (24kbps+24kbps) will get through without any issue. If you try to place a third g.729 call, call will get through but voice quality of ALL CALLS will be degraded. This can only be avoided by setting proper BW settings in Location parameter.

@Xenix Thanks!

Where is Standar Local Route Group configuration applied?

in each device pool? or in each route list?????

Someone can tellme what is the correct answer?

@SC
You mean to say there are different options or different answers in Xenix’s dump?

@Cris

In Each Device Pool.

@Reyvan,

Different answers in the real exam. But about 2or3 questions + 2or3 new questions…the rest from the dump.

@SC 🙂 Thanks dude..

@SimplyCasual, what’s passing? 790?

I move to CIPT2 now. All the best for all!

See u there 🙂

Hello All,

Can anyone please help me to understand what would be Incoming calling number if I have selected ‘Use Device pool CSS’ in Incoming calling party transformation settings and my Device pool CSS = Default.

If we have selected ‘Use Device pool CSS’ checkbox, sequence is:
1) Strip digits
2) Add prefix
3) Use Device pool CSS (ignored Calling Search Space)

Hi Azon,

Thanks for your reply but what if Device pool CSS is set to Default.

Lets discuss an example.

Incoming calling number = 00492288224002
Strip digits = 2
Prefix = +
Use device pool CSS is selected

Device pool CSS = Default

What incoming number it would show on IP phone?

+492288224002 for this example.

But on exam this question with TON=Unknow, without digit manipulation. Correct answer will be 00492288224002

Passed today, but damn it was close. I’d really suggest everyone get the CIPT1 book and go through it. Get CBT nuggets as well.

Hi All,

Can someone please help me to clear confusion for below question.

Which three Cisco Unified Communications Manager settings can be used to support IP phone services? (Choose three)

A. Device Defaults
B. Enterprise Parameters
C. IP Phone Service configuration
D. Common Phone Profile
E. Service parameters
F. Phone Configuration window

As per Xinix answer is – BDF
but I think it should be – BCF

@Ciscodude

How many questions was there in exam? any new questions? If you remember can you please post new questions. thanks

I’d say 6 or 7 new questions, and some current ones with different answers. Sorry I can’t remember them, I was far too nervous about passing. If you hit the videos and questions you should be fine, I didn’t dedicate a ton of time to studying CIPT1. I was more focused on CIPT2, which I passed the day before CIPT1 haha.

@ciscodude
Do you remember the subjects of the new Q?

I just passed with 848, It was really hard.
it was like 10 to 20 new Questions, from Xinix dump i have like 35 questions with the same answer, and like 15 more with diferent answer.

I remember this new One:
If there are SIP dial-rules configured, what are the advantages (select two):
A. You can dialing a phone without any communications with CUCM of signaling traffic.
B. You receive a reorder tone if the number is not allowed without any communications with CUCM signaling traffic.
C…
D..
E..
I don’t remember the other choices, cause i doubt between A and B, I select B and the other choice was very easy I think it was D.

From Xinix dump I remember this one:
Users that are subscribed to the default corporate directory are complaining that when they press the Directories button, they receive an error message regarding the URL. Which two parameters need to be edited?

—The answers are the same, but you have to choose TWO answers, in xinix dump you only have one choice, so you have to read and find the other choice….

Thanks for all your help, I’m going to start study CIPT2….

Good luck every one.

QUESTION 106
Which of these is a characteristic of the Cisco Unified Communications Manager Bulk Administration Tool in
Cisco Unified Communications Manager 6.0?
A. Cisco Unified Communications Manager Auto-Register Phone Tool is part of Bulk Administration.
B. Cisco Unified Communications Manager BAT needs to be installed from the plug-in page.
C. Cisco Unified Communications Manager BAT pages are available from the Serviceability page.
D. Cisco Unified Communications Manager Auto-Register Phone Tool requires a Customer Response System.
Answer: A or D ???

Guys what do you think ???
to me I feel “D” is more suitable 😀

anyone can tell me
hpw to study CIPT1v8
from the CIPT1 v6 or what ???
and how to help in the rest

@Network Engineer
You can study from the old version CIPT1 v6 Implementing-CUCM-part-1-cipt1(642-446), that’s what i did.

Hey Guys is there any labs in this exam???

@vishal
No labs

Even a monkey can pass by using dumps

@ALL
Everybody can access CIPT1 FLG book at SafariBooks by using coupon code RGDLPEH
http://www.informit.com/safarifree

pass yesterday, with 871
about 5 or 6 new questions, but you can find the right answer easily

Passed with 883.
about 5 new questions, used CIPT 6.0 book and CBT. Most of the question from Xinix’s dumps.

I’m trying to write this exam from past 3 days, but im not getting a slot for whatsoever reason .. I prepared Xenix’s dumps and Jeremy’s CBT nugget for cipt1 .. Guys who are done with the paper can you please share the new questions?

Thanks a lot !!

@ Revan : Congrats dude, I’ve read all the comments in this page from comment #1 to the one i’ve posted now, many of you guys have helped us to share the tricky and confusing questions, as i said im trying to write this paper since last 3 days, but unlucky to get a slot .. hopefully il get a slot tomorrow .. Will share my experience ASAP 🙂 ..

Guys one more question :

When Cisco Unified Communications Manager is in default configuration, why are all calls possible for all calling sources?

A) Because all entities are placed in the partition and in the css.

B) Because all entities are placed in the partition and in the css.

C) Because entities that do not have a CSS assigned can only access calling targets without a partition assigned.

D) Because any calling target can only reach those calling sources that are in the CSS.

In Xenix’s dump, Ans = C

But i guess it should be Option ” A ” { If the CSS == CSS } …

Need your opinion guys ..

Correct Options :

A) Because all entities are placed in the (none) partition and in the (Default) CSS.

B) Because all entities are placed in the (Default) partition and in the (Default) CSS.

C) Because entities that do not have a CSS assigned can only access calling targets without a partition assigned.

D) Because any calling target can only reach those calling sources that are in the (Default) CSS.

it’s called “None” CSS not “defualt” CSS

@AKS : Thanks buddy, and best luck for your exam.

Hi Guys, I cleared the exam with 83X marks .. There were around 5-6 new question and few question of dump had different options, and i one or two question we had to select 2 options ( but in the dump it had only 1 option as answer ) .. I got almost all the tricky question in the exam for example 1) Which of these ” Can Be ” hardware based media resource .. and 1 more was 2) Which Service needs to be run for it to work as Publisher .. etc … Il post you the New Questions asked in the next note as this is getting little congested =P

New questions : ( Well i dont remember the entire question, but il highlight the imp words of the question, with which you can recognize it )

1) Its related to Partition and CSS, you have 5 phones in the exhibit with separate partition and CSS, applied to it … ( Imp*: 1 phone doesn’t have a partition and 1 phone doesn’t have a CSS )

Ans : Phone 2, Phone 3 and Phone 4 ( my answer ) …

2) I got 2 questions for which answers were kind of same .. It had ” presence ” directory in the question.

Ans : Combined Phone Device and Subscribe CSS ( And in Dump we have one more ques for which the ans is Presence Group and Subscribe CSS )

3) When CUCM is installed, how can the Customer Use the Operating system?

Ans : It can be accessed by Cisco TAC only[my answer] ( well this question is kinda tricky because, no 1 has a full access to the OS excluding CISCO TAC, we as an admin have few commands for troubleshooting purpose i guess, Please confirm this with someone who knows about this .. Many said the answer can be ” CLI and GUI ”

4) One question was regarding , when phone is registered which server it will register with?

Ans : As we know it goes through the list in cucm group list from top to bottom, there was same option so i selected the same …

5) which media resource can be configured in the cucm? ( Choose 3 )

Ans : MOH Server, Autoattended, Conference Bridge

6) This was related to sip phone, The question has ” With a type of SIP A phone ”

Ans : option a. ( type of Sip A Phone )

Hi Friends,

about to give the cipt 1 exam with in a month, so kindly wanted to know, if there is a specific dump and book link that can be followed to get the necessary details to study, would really appreciate if somebody can guide me on the same

Regards,

Abhishek Singh

@AKS : I had also got same question about accessing OS. Correct answer should be CLI & GUI. Here the hint is ‘OS’, if the question would have asked for root access then answer would be Cisco TAC only.

@ Revan : Yes might be, so i guess my marks got deducted there, Btw did u complete your CVOICE paper? I’m left with only CVOICE .. I’m Done with rest 4 papers ..

@ Abhishek Singh :
You can study from Xenix’s dump 219q and go through the CBT nuggets of jeremy cioara , if you have a book/quick referece for cipt1 please go through that as well, gain all possible knowledge as you can before sitting for the exam, as you said you have around 1 month of time, i guess you can go through these dumps videos and books for sure .. All the best for your preparation …

Pass CIPT1 today and on to CIPT2 now. Xenix’s dumps are still valid although the wording on some of the questions has changed and a few new questions were introduced.

@SimplyCasual – Thanks for the share!

Hi,

I am planning to take CIPT1 v8.0 642-447 exam shortly. Looking for good study materials and related helpful information. Please kind enogh if anyone can help me in this regard.

Thanks

Peter

Hi,

I am planning to take CIPT1 v8.0 642-447 exam shortly. Looking for good study materials and related helpful information. Please kind enogh if anyone can help me in this regard.

Thanks

Peter

@sysco….

cvoice learning foundation guide by kevin wallace..its an awesome book dude…i m sure this will meet your requirements…

@AKS: sorry dude, I had given CVOICE last year (as per old syllabus). I don’t have latest material for CVOICE.

Hi Aks,

Thanks for the wishes mate. i do have the nuggets from jeromy ciora but they are for the old version of the cipt .. 642-446 , and apart from that the only source that i have are these nuggets.. isnt there a rough cut for the same so that we can not only prepare from these dumps but can also get an understanding for the same ( through some bookish material ..ala the rough cuts )

Hey Aks,

You gave ccna voice last year, i gave my ccna voice in august and plan to give cipt 1 before 27th october , and cipt 2 some time before 2 november and and ccvp exam before 20 November

Catch : I was a cisco tac engineer , had vouchers , which are due before these dates. Am i not doing a suicide by giving the exams back to back, though cleared my ccna voice with one week prep 🙂 , so just wanted to know, should i go ahead with all the exams ( for the sake of vouchers.. and with a lot of firefighting ) or should i go for it slowly and steadily ( personally i want to give it in firefighting mode.. back to back ) 🙂

q. users that are subscribed to the default corporate directory are complaining that when they press the directories button , they receive an error message regarding the URL.

Which two parameteres need to be edited ? ? 2 options are asked.. and in the answer only the ” change the url under enterprise parameter to match the dns name or the ip address being used by the server being configured and reset the phones.

what would be the second parameter , is there a second answer .

Hi , The last anonymus individual was me only 🙂

The new COIVCE, CIPT 1 & 2 books (version 8.0) may be found here:

http://www.wowebook.com/category/networking/

hey homesambiguity, went to this link, but not able to download the rar file.

@HomesAmbiguity Thanks a whole lot!!!! Downloads appear to be virus free.

Hey MARV,

I was not able to download the file from the link, as it shows server not connected all the time. Can you kindly share the file..would really appreciate that .

Plz send me any one Latest Dumps for CIPT 1 and 2 V 8.0

q. users that are subscribed to the default corporate directory are complaining that when they press the directories button , they receive an error message regarding the URL.

Which two parameteres need to be edited ? ? 2 options are asked.. and in the answer only the ” change the url under enterprise parameter to match the dns name or the ip address being used by the server being configured and reset the phones.

what would be the second parameter , is there a second answer .
——————————————————————————————————————

@Abhishek Singh, the options to this question are:

a) Reset the service parameter -> Phone URL parameter
b) Reset Enterprise Phone URL parameters
c) Select the Service parameter for the appropriate server and CCM (active) and change the URLs for each service to match the DNS name or IP Address of the server being configured.
d) Change the URL under Enterprise parameter to match the DNS name or the IP Address being used by the server being configured and reset the IP Phones.
e) verify that the corporate directory has the Enabled check box checked in the IP Phone services -> configuration service information page.
f) Verify that the corporate directory has the Enabled check box checked in the Enterprise parameter -> Phone URL parameter page

I think the second answer is option ‘E’ according to my investigation, in addition to ‘D’.

I will appreciate people to also confirm this before making up my mind.

I have a set of answers from Xenix material which I disagree.

1) Which 4 of these resources can be hardware-based in CUCM?
a)MOH b)voice termination c)MTP d)Annunciator e)Trancoding f)Audio conferencing

Xenix Ans: ACF, My ans: BCEF

2) What is the minimum number of partitions that must be defined given the dial plan rules listed below:
– All employess can call local and service numbers
– ….
– ….
– …
– Incoming calls can only be routed to phones, not trunk

Xenix Ans: 5 , My Ans 4
I dont understand why the last rule should require a separate partition. I need clarification somebody please help.

just cleared my exam – 848, nearly 12 questions were different and the other from xenix had the questions rephrased in a different manner.

Be careful and please go through all the comments by the members here… thanx to selcius and other important members of the forum for there support.

onto cipt 2 next week.

Guys, is there any forum or site where we can discuss job related/Interview question’s for CCNP-Voice ( CCVP ) …???

hi Guys,
Pls share a link to download the CBT Nuggets for CIPT1 v8.0 642-447.

Passed today 860

Xenix is still valid

3-4 new questions , 6-8 with different answers .

any updates on the exam? thanks

any updates on the exam? ill be taking the exam next week

Could anyone please provide a list of new questions, that are not in Xenix dump ?
I’m gonna take exam 11.18.

@day_that_i_die
i think no one is taking the cipt1 right now. can you update the questions once you take the exam? thank you very much

any updates on the new questions on the exam? highly appreciated. thanks

Hi Guys, I am planning to take CIPT 1 in next week. I am practising on CUCM 8.5, I have installed on VMWARE with 2 softphones.. However, I need dumps.. could you please share latest dumps?

I’ll be taking my exam on the 25th of November..

Kindly please post the new questions here.. i will really appreciate it. thank you very much

Hi

I have a CallManager Cluster (ver 6.1) and a voice gateway (Cisco 3945). All my other gateways are running mgcp but this one cant as CUCM 6.1 does not support 3945 using mgcp.

Routing to and from a site using a 3945 works 100% using h323. Only problem is that when you’re calling a mobile number, and press decline on the mobile, the Cisco IP phones is still getting a ringback tone for a couple of second and finally gets a user busy tone and message on the screen.

Where can I configure this?

I’ve ran traces on the gateway and I see a User Busy message but CallManager does not clear the call:

025993: Nov 22 14:43:15.722: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0xA771
Cause i = 0x8091 – User busy

Please advise

Passed today with 825 ! Xenix dump still valid. See you on CVOICE

Never mind. Global config command: voice call disc-pi-off solved the problem.

@DSK

do you remember the new questions on the exam?

Hi m gonna take CIPT1 exam on 28th …any idea about new question guys ?

passed with 905 \m/ =)

Congrats VoiceVoice..
Plzz Share ur xperience wid uss… i think ur d 1st 2 score abv 900.. Gr8 Job Bro.. 🙂

Xenix dump plus the new updated vce file

@ VoiceVoice…
Is der ny changes in Xenix Answer’s??? or r all Correct???

@VoiceVoice ..dude how can I get that new update VCE file ?

i modified something. but most of the answers are correct..
You can pass with xenix dumps.

any body have a new P4S for the Exam 642-447 , i have a paper after 4 days, please tell me and how many questions are wrong & how much question are out of P4S ?

hey passed with 906 marks ..:)
Xenix is still valid..

@MSK

could you help us in providing the new update VCE file??? what exactly new update vce file, and where we can find it?? your help is appreciated.

@ccna voice
this is one is new updated file …although it is same as Xenix only 3 4 new questions are added and in exam i got onlly 3 new questions otherwise whole xenix dumps were there..

http://www.examcollection.com/cisco/Cisco.ActualTest.642-447.v2011-10-17.226q.vce.file.html

@MSK

thanks a lot for your help…appreciated..

@HomesAmbiguity, or everyone else..can we discuss the errors seen on the CIPT1 (642-447) book by Josh Finke and Dennis Hartmann.

I think the book is on point but some sections of the book are misleading or please refer me to the relevant forums

Thx

I have installed CUCM 8 in Vmaware… everything is wrking well… But during registration of Cisco IP-Communicator.. It nt gettin registered.. I think the issue is in TFTP server… i hv given ccm ip address as a tftp server.. m i correct??

Ny help ll b appreciated!!!! Thannnxxx..

@Lord

make sure tftp server is the cucm ip of the sub/pub( if u use pub as a tftp) is correct, and also check with .loads file …

ccnavoice..

Gt it… the tftp service ws nt activated by default in cucm.. 🙂

Do u hv ny lab setup.. i hv nly cucm installed in vmware n CIPC..