Share your ICOMM Experience

1) What storage element does TCS use to store recordings?

Answers:
– locally (default E: drive)
– NAS
Resource:
https://www.cisco.com/c/en/us/td/docs/telepresence/tcs/7_0/admin/administration/tcs_7_0/storage.html

3) What’s the CLI command in CUCM to unlock the admin account after 2 minutes?

Answer:
utils reset_ui_administrator_password

Resource:
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/cli_ref/8_6_1/cli_ref_861.html#72751

4) What are things to avoid when setting a telepresecence room?
-avoid glossy objects
-plants and decorations

Answers:
– no direct answer in the documentation:
https://www.cisco.com/c/dam/en/us/solutions/collateral/collaboration-endpoints/c07-643449-00_tp_dg.pdf
but I can agree with the first for sure as there is stated to avoid reflective objects,
regarding plants and decorations, probably too but would be better to have all possible answers to choose best.

I pass my exam 973/1000
210-060

One question regarding settings LDAP in CUCM, which are require or similar (Choose two options)
A. System>Enterprise Parameters
B. LDAP>LDAP System
C. LDAP>LDAP Directory
D. LDAP>LDAP Directory > LDAP Directory synchronization

@Voicehelp, thanks. Please check this question:

QUESTION 242: Users are complaining about dropped calls, so a network engineer needs to troubleshoot Cisco Unified Communications Manager to view concurrent calls and dropped calls. Where does the engineer generate such reports?

A. Cisco Unified Serviceability
B. Cisco Unified OS Administration
C. Cisco Unified Communications Manager Administration
D. Cisco Unified Real-Time Monitoring Tool

Answer: C or D?

@Kris please share more with us THX

@Imran which dump is ? =0

@Imran
NEW QUESTION 299
An engineer is modifiying a dial plan for a ciscco unified communications manager system and notices that the new route patterns are not properly manipulating the dial string. Which configuration element must the engineer check to determine the cause?

A. phone
B. phone DN
C. route list
D. dial peer

Correct answ is C not D

@Voicehelp, Can you help with this:

210-060 NEW
One question regarding settings LDAP in CUCM, which are require or similar (Choose two options)

A. System>Enterprise Parameters
B. LDAP>LDAP System
C. LDAP>LDAP Directory
D. LDAP>LDAP Directory > LDAP Directory synchronization

@Luka M
What’s the question ?!?!?

@Luka M
The basics steps to set up LDAP sync are as follows:
Step 1. Activate the Cisco DirSync service.
Step 2. Configure the LDAP system.
Step 3. Configure the LDAP directory.
Step 4. Configure LDAP custom filters.

210-060 NEW
One question regarding settings LDAP in CUCM, which are require or similar (Choose two options)

A. System>Enterprise Parameters
OPTIONAL

B. LDAP>LDAP System
MANDATORY
– here you have to “Enable Synchronizing from LDAP System” checkbox

C. LDAP>LDAP Directory
MANDATORY

D. LDAP>LDAP Directory > LDAP Directory synchronization
– no such option
– you can here “LDAP > LDAP Directory” configure “LDAP Directory Synchronization schedule”

ANSWERS: BC

@johnson THX , have you pass the exam ?

@Imran,
Could you pass the CICD 210-060 exam? How much score did you get?

@Voicehelp, here you are some question
Q1
Users are complaining about dropped calls, so a network engineer needs to troubleshoot Cisco Unified Communications Manager to view concurrent calls and dropped calls. Where does the engineer generate such reports?
A. Cisco Unified Serviceability
B. Cisco Unified OS Administration
C. Cisco Unified Communications Manager Administration
D. Cisco Unified Real-Time Monitoring Tool
Answer: D

Q2
Which two password options are there to set up voicemail (for multi-users)?
A. User Cannot Change
B. No Password
C. Does Not Expire
D. User Must Change at Next Login
E. Locked By Administrator
Answer: AC

Q3
A voicemail user reports that he cannot access Cisco Unity Connection from the IP phone message button. Which option must you perform to resolve the problem?
A. In Cisco Unified Communications Manager, navigate to Advanced Features > Voicemail to confirm that the user has the correct voicemail profile
B. In Cisco Unified Communications Manager, navigate to Device > Phone to confirm that the device has the correct voicemail profile
C. In Cisco Unified Communications Manager, navigate to Device > Phone to confirm that the directory number has the correct voicemail profile
D. In Cisco Unified Communications Manager, navigate to user Management > End User to confirm that the user has the correct voicemail profile
E. In Cisco Unity Connection, navigate to Users > Users to confirm that the user web password is correct
Answer: C

Q4
IP Phone user report that the MWI light does not work while receiving voicemail messages which action must be taken to troubleshoot in Unity Connection?
A. Run port activity report
B. Reset the phone
C. Reset MWI function in unity connection
D. Check user mailbox
Answer: A

Q5
A manager is generating bill reports for a particular user. Which navigation sequence must be used for this task?
A. Bills > Department
B. User Reports > Bills > Department
C. Bill > Individual
D. User Reports > Bills > Individual
Answer: C

Q6
Which scenario allows user A in partition X to call user B in Cisco Unified Communications Manager?
A. User B in partition X is not assigned to any CSS.
B. User B in partition Y assigns both partitions to CSS-X.
C. User B is not assigned to any partition or CSS.
D. User B is assigned to partition Y and assigns to CSS-X.

Answer: C
Q7
How many phones can be registered on the standard cluster?
– 40.000 phones maximum

Q8
When you change the security profile for a phone in CUCM, what happens?
A. *Rebuild The .xml file of the phone X

Q9
Under phone configuration what option is used to add conference bridges?
A. *Media resource group list

Q10
In which three ways does QoS provide better network service VoIP quality? (Choose three.)
A. minimizes priority queuing
B. manages network congestion
C. improves loss characteristics
D. supports dedicated bandwidth
E. decreases traffic priorities
F. increases packet size
Answer: BCD

Q11
An engineer is configuring Cisco Jabber for iOS. The device name must start with which option?
A. CSF
B. TCT
C. iOS
D. BOT
Answer: B

Q12
Which command adds a second line to an ephone-dn?
A. ephone 1 lines 2
B. ephone-dn 1 lines 2
C. ephone-dn 1 dual-line
D. ephone-dn 1 secondary line add
Answer: C

Q13
An engineer must import many users at the same time into Cisco Unity Connection. Which method must be used?
A. manual creation
B. CAPF profiles
C. COBRAS
D. bulk administration
Answer: D

Q14
A network engineer must perform a manual backup of the Cisco Unified Communications Manager system. Where can this backup be done?
A. Administration Resources
B. Serviceability
C. OS Administration
D. Disaster Recovery System
Answer: D

Q15
A customer has requested that all employees have “Standard CTI Enabled” and “Standard CCM End User” roles. How would these be assigned prior to being applied to their accounts?
A. Default Device Profile
B. Credential Policy
C. User Profile
D. Access Control Group
Answer: D

Q16
An administrator is setting up a remote site in Cisco Unified Communications Manager that has a T1 WAN connection to the main site. Which option is the best VoIP codec for this task?
A. G.711
B. G.729
C. G.712
D. G.723
Answer: B

Q17
An engineer is ensuring that each SIP-based element within a network has a component to route call activities to. Which virtual Cisco UCS server component is effective in reducing the number of call routing combinations while also simplifying SIP network design and troubleshooting?
A. PBX
B. Cisco Unified SIP Proxy
C. VG Gateway
D. SRST
Answer: B

Q18
An engineer is creating a new phone using the Call Manager. Which option is presented first when you click the Add New button?
A. Phone Type
B. BAT Phone Template
C. MAC Address
D. Common Phone Profile
Answer: A

Q19
You want to configure caller ID to display a user name instead of a dn for internal callers. Which of the following line appearance fields should you modify in UCM? (Choose the best answer.)
A. Display
B. External Phone Number Mask
C. Line Text Label
D. Visual Message Waiting Indicator Policy
Answer: A

Q20
You click Administrator’s Login Account in the CME GUI’s Configure System Parameters menu. Which of the following are you most likely configuring? (Choose the best answer.)
A. a customer administrator
B. an LDAP administrator
C. a phone administrator
D. a system administrator
Answer: A

Q21
A user in Cisco Unified Communications Manager Administration has been added to the Standard CCM Admin Users group, which includes the Standard CCMADMIN Administration role, but the user cannot add new users. What is the cause of this issue?
A. The add user capability has been disabled for the group
B. The incorrect group and role were assigned.
C. The add user capability has been disabled for the role.
D. Only the CCMAdmin user can add users.
E. Users can be added only via LDAP.
Answer: B

@Kris, are you sure that´s CICD questions are right?

Q1, someone says C.
Q5, someone says D.
Q6, someone says B.
Q21, someone says C.

Check them carefully please!

@Kris THXX 🙂

@Voicehelp, please confirm the CICD questions Q1, Q5, Q6 and Q21.

@Voicehelp, confirm CICD 210-060 please:

NEW QUESTION 293: John wants to configure a dial peer on his voice gateway. Any user who calls 1234 must always hit the inbound dial peer “dial-peer 100”. Which configuration correctly implements this requirement?

A. Dial-peer voice 100 voip
Destiation-pattern 1234

B. Dial-peer voice 100 voip
answer-address 1234

C. Dial-Peer voice 100 voip
answer-address 1234

D. Dial-peer voice 100 voip
incoming called-number 1234

Answer: A or C?

ALL
Q2
Which two password options are there to set up voicemail (for multi-users)?
A. User Cannot Change
B. No Password
C. Does Not Expire
D. User Must Change at Next Login
E. Locked By Administrator
Answer: AC

definitive explanation

Password Settings
CUC uses two separate passwords for each user: The web application password is used for logins to CUC web pages (including the user web pages, and administration pages if the user has the privilege to access them); the voicemail password is actually the PIN, which is used for TUI logins. To begin, select which password you want to configure. On the page that opens, select or modify the following options:
■ Locked by Administrator: Select this if you want to prevent the user from logging in to CUC.
■ User Cannot Change: Select this to prevent the user from changing his password. This is recommended if more than one user will access the voicemail box; it is also recommended in this case to select the Does Not Expire check box.
■ User Must Change at Next Login: Select this to force the user to change his password the next time he logs in to CUC.
■ Authentication Rule: Set the Authentication Rule that will be applied to the user account’s password.

Hey guys this question will be on 210-065. What is the command to unlock the admin account on CUCM in 2 minutes. Remember that the answer is in seconds not minutes.

set accountlocking unlocktime 120

Configures the unlock time for the current Unified Communications Manager admin accounts

@ Luka Modric

Q1, someone says C.
A. Cisco Unified Serviceability – here you can set Trace configuration
D. Cisco Unified Real-Time Monitoring Tool – here you can generate report

Q5, someone says D.
C. Bill > Individual – generate by manager
D. User Reports > Bills > Individual – generate by administrator

Q6, someone says B.
C. User B is not assigned to any partition or CSS. – then will use default settings which are available for all partition

Q21, someone says C.
The Standard CCM Admin Users role includes no permissions beyond logging into Cisco Unified Communications Manager Administration. The administrator must add another authorization role to define the parts of the Cisco Unified Communications Manager Administration that the user can administer.

@Kris THX !

Inbound Dial Peers Matching Process

The router or gateway matches the information elements in the setup message with the dial peer attributes to select an inbound dial peer. The router or gateway matches these items in this order:

1.
Called number (DNIS) with the incoming called-number command

First, the router or gateway attempts to match the called number of the call setup request with the configured incoming called-number of each dial peer. Because call setups always include DNIS information, it is recommended to use the incoming called-number command for inbound dial peer matching. This attribute has matching priority over the answer-address and destination-pattern commands.

2.
Calling Number (ANI) with the answer-address command

If no match is found in step 1, the router or gateway attempts to match the calling number of the call setup request with the answer-address of each dial peer. This attribute can be useful in situations where you want to match calls based on the calling number (originating).

3.
Calling Number (ANI) with the destination-pattern command

If no match is found in step 2, the router or gateway attempts to match the calling number of the call setup request to the destination-pattern of each dial peer. For more information about this, see the first bullet in the Dial Peer Additional Information section of this document.

4.
Voice-port (associated with the incoming call setup request) with configured dial peer port (applicable for inbound POTS call legs)

If no match is found in the step 3, the router or gateway attempts to match the configured dial peer port to the voice-port associated with the incoming call. If multiple dial peers have the same port configured, the dial peer first added in the configuration is matched.

5.
If no match is found in the first four steps, then the default dial peer 0 (pid:0) command is used.

Matching Outbound Dial Peers
In order to match outbound dial peers, the router or gateway uses the dial peer destination-pattern called_number command.

On POTS dial peers, the port command is then used to forward the call.

On Voice-Network dial peers, the session target command is then used to forward the call.

Also, when outbound peers are matched, there are two cases to consider: DID case and non-DID.

@ All, Could you share experience regarding 210-065 ? 🙂

Are there someone who is preparing for certification CICD 210-060 ?
I need a course support to get started

@Kris, Voicehelp

QUESTION 1: Which two technologies comprise a Cisco Presence deployment? (Choose two.)

A. Cisco Unified Presence Server
B. Cisco Unity Connection
C. Cisco Unified Communications Manager
D. Active Directory
E. Cisco Unified Border Element
F. Cisco Expressway

Answer: AC or BC?

@luka – answer is AC – Unity Connection is used for Voice Mail

Congratzzz BRo!!! Which Dumps u had followed.? n hw many D&D ws der in xam.. culd u plss share with us..?

n regarding ur ans..(about the services need to be publisher)… Call manager & TFTP Server

I think its nt correct…
1) DirSync:
DirSync has to be activated on the publisher server because the publisher is the only server in the CUCM cluster with read/write capabilities and information is being inserted into the CUCM IDS database.( So, i think it should be activated on Publisher).

2) Cisco DHCP Monitor Service
Cisco DHCP Monitor Service monitors IP address changes for IP phones in the database tables. When a change is detected, it modifies the /etc./dhcpd.conf file and restarts the DHCPD daemon. ( Cisco recommends that DHCP Monitorfw Service should be activated on Publisher)

3) Call manager: It is not necessary(wefecommended by cisco ) that Publisher should be involved in call processing..(The basic function of call manager service is to process the call in ur system/organization) If there are more than 1000 Ip-Phones in ur organization… ( so, i think its not mandatory to aesvctivate call manager servic on publisher)

4)To avoid performance issues, Cisco recommends that you configure a dedicated TFTP server (separate from the Cisco CallManager server) if you have many phones and gateways in your network…

…..Cisco CallManager and Cisco TFTP services can run on the same server in small configurations only (for example, in a network with fewer than 2500 phones)….

from my opinion.. the answer should be Dirsync n DHCP Monitor Service
dwa
This above Info. i hv got from various Cisco books/forums/& also from some expert advice…

@CCNA Voice.. we wuld lyk to read ur overall xam experience.. so.. plss shar with us.. Thanx

@Willow,

Labs the same … lol :D:D:D:D:D

210-065

Q66: Which 3 features are supported by CVS encoding Server?
A: IP and analog cameras
B: MPEG-2 and MPEG-4 encoding
C: archiving
D: motion detection
E: clustering
F: virtual matrix

Dumps say ABD, but according to: https://www.cisco.com/c/dam/en/us/td/docs/security/physical_security/video_surveillance/network/design/vsmrg_v2.pdf

better answer is ACD

What do you think?

A desktop video endpoint is needed that can support a PrecisionHD camera design and a built-in display, and is Bluetooth-ready and multisite-capable. Which desktop endpoint supports all of these requirements?
A. SX20
B. EX60
C. SX80
D. EX90

SX-series has no built-in display, EX60 does not support multisite

Answer: D

An engineer is configuring a Cisco TelePresence System endpoint for use with a maximum of six people in the room. Which table type should be configured when setting up cameras where two participants directly face the endpoint display?
A. short racetrack
B. long racetrack
C. short rectangle
D. long rectangle

short racetrack – 2 participants face camera
long racetrack – 4
short rectangle – 4
long rectangle – 6

Answer: A

Can someone please tell me is this dumb still valid or which one is valid?

cisco.pass4sure.210-060.v2018-02-05.by.andre-remonkkk.250q.pdf

I’m planning take cisco 210-060 soon and go back page 72 to present page to copy all the question’s that those people are a passed the exam. Can someone please verify all this question’s and Thank you in advance. Also, can someone please tell me what the lasted dumb for 210-060?

QUESTION 1
An engineer is configuring the Cisco Unified Communications Manager disaster recovery system. Which three statements about the disaster recovery system are true? (Choose three.)
A. It requires the use of schedules for backups.
B. Backup files are encrypted using the cluster security password.***
C. If the backup device is listed in a backup schedule, it cannot be manually deleted. ***
D. If the backup does not complete within 40 hours, the backup times out.
E. Archiving backups to tape drives is supported.
F. SSL is used between the master and local agents. ***

QUESTION 2
A network administrator finds directory number 77555 in the partition. Which numbers can reach 77555 in this situation?
A. Only numbers in the partition can reach 77555.
B. All numbers in every calling search space can reach 77555.***
C. Only internal directory numbers can reach 77555.
D. Directory number 77555 cannot be reached by any number.

QUESTION 3
What is the maximum amount of packet loss an engineer should allow for voice traffic on an IP network?
A. 5 percent
B. 2 percent
C. 3 percent
D. 1 percent ***

QUESTION 4
An IT administrator must allow a customer service department supervisor to change or modify a recorded message on their phone system. Which role is needed to accomplish this?
A. Greeting Administrator ***
B. Recordings Administrator
C. Remote Administrator
D. Annunciator Administrator

QUESTION 5
Which component allows Cisco Jabber to communicate with clients who are outside the corporate network?
A. Cisco Extension Mobility
B. Cisco TMS
C. Cisco Mobility Remote Destination
D. Cisco Unified RTMT
E. Cisco Mobile and Remote Access ***

QUESTION 6
What are three ways for an administrator to create users in Cisco Unity Connection? (Choose three.)
A. Use the Bulk Administration Tool ***
B. Import from Cisco Unified Communications Manager Express
C. Import from a Microsoft Word document
D. Import from an Adobe PDF document
E. Use manual creation ***
F. Import from a Microsoft Outlook contacts list
G. import from LDAP ***

QUESTION 7
Users are complaining about dropped calls, so a network engineer needs to troubleshoot Cisco Unified Communications Manager to view concurrent calls and dropped calls. Where does the engineer generate
such reports?
A. Cisco Unified Serviceability
B. Cisco Unified OS Administration
C. Cisco Unified Communications Manager Administration
D. Cisco Unified Real-Time Monitoring Tool***

QUESTION 8
A user presses the envelope button on a 7945 IP phone, but it only launches audio voicemail. Where should the voice systems administrator troubleshoot?
A. Visual voicemail IP phone service in Cisco Unity Connection
B. Visual voicemail IP phone service in Cisco Unified Communications Manager ***
C. SIP trunk between Cisco Unified Communications Manager and Unity Connection
D. IP phone network connectivity

QUESTION 9
Which address is required to create a video endpoint in Cisco Unified Communications Manager?
A. MAC ***
B. IP
C. E.164
D. SIP URI

QUESTION 10
A Cisco administrator is asked to set up two new end users in Cisco Unified Communication Manager. Which two fields are required? (Choose two.)
A. First Name
B. User ID ***
C. PIN
D. Telephone Number
E. Password
F. Last Name ***

QUESTION 10
Jabber for iOS is which Device Name?
A. CSF – Jabber for Desktop
B. TCT – Jabber for iPhone ***
D. BOT – Jabber for Android

QUESTION 11
A Cisco IP phone is connected to a Cisco switch and is trying to obtain its network configuration. What is
the first protocol that is used?
A. RTP
B. DHCP
C. CDP ***
D. SIP

QUESTION 12
An IT administrator integrated the Cisco Unified Communications Manager cluster with the corporate Active Directory server using the Lightweight Directory Access Protocol. However, after accessing the Cisco Unity Connection Administration section of the CUC cluster web interface, the IT administrator cannot access LDAP Directory from Users> Import Users. Which two problems have occurred? (Choose two.)
A. The Cisco Unity Connections Primary server must be restarted.
B. LDAP synchronization must be enabled.
C. The LDAP configuration in Cisco Unified Communications Manager must have the Cisco Unity Connections LDAP integration in Cisco Unified CM Administration option enabled.
D. The Cisco Unity Connections HA server must be restarted. ***
E. The LDAP Directory Configuration must be completed in the Cisco Unity Connection Administration interface. ***
F. The LDAP authentication settings are incorrectly specified in Cisco Unity Connections.

QUESTION 13
Which two user attributes must be defined in Cisco Unity Connection before the users can be added? (Choose two.)
A. Display name
B. Alias
C. Time zone
D. Class of service ***
E. Dial plan ***

QUESTION 14
A user directory number is configured to forward all calls to a cell phone, but calls are not successfully forwarding. Which Cisco Unified Communications Manager setting requires reconfiguration?
A. DN External Mask
B. DN Route Partition
C. DN Calling Search Space
D. CFA Calling Search Space ***

QUESTION 15
An engineer must ensure that user data is maintained in lightweight directory access protocol and copied to Cisco Unity Connection, but Cisco Unity Connection-specific data is locally maintained in the Cisco Unity Connection database. Which user creation option accomplishes this task?
A. Bulk administration
B. Import from CUCM via AXL
C. Import from LDAP ***
D. Manual creation

QUESTION 16
A manager is generating bill reports for a particular user. Which navigation sequence must be used for this task?
A. Bills > Department
B. User Reports > Bills > Department
C. Bill > Individual
D. User Reports > Bills > Individual ***

QUESTION 17
A user reports that during calls they hear excessive hissing when neither party is talking. Which option is one cause of this noise?
A. QoS
B. LoPS
C. VAD ***
D. EPL
E. SRST

QUESTION 18
A voicemail user reports that he cannot access Cisco Unity Connection from the IP phone message button. Which option must you perform to resolve the problem?
A. In Cisco Unified Communications Manager, navigate to Advanced Features > Voicemail to confirm that the user has the correct voicemail profile
B. In Cisco Unified Communications Manager, navigate to Device > Phone to confirm that the device has the correct voicemail profile
C. In Cisco Unified Communications Manager, navigate to Device > Phone to confirm that the directory number has the correct voicemail profile ***
D. In Cisco Unified Communications Manager, navigate to User Management > End User to confirm that the user has the correct voicemail profile
E. In Cisco Unity Connection, navigate to Users > Users to confirm that the user web password is correct.

QUESTION 19
A voice engineer has installed an XML-based phone application from a third party and subscribed a user’s 7945 IP phone to the application. Which action does the user take to launch the new service on the IP phone?
A. Select the Applications button on the 7945 IP phone.
B. Select Settings > Applications.
C. Select Settings > Network > Applications.
D. Select the Services button on the 7945 IP phone. ***

QUESTION 20
How are calls routed in an MGCP call agent?
A. By route patterns on Cisco Unified Communications Manager ***
B. By dial peers on the gateway
C. By static routes on the gateway
D. By a translation pattern on Cisco Unified Communications Manager

QUESTION 21
Several users in the same Call Manager group reported that they receive a fast busy tone when they go off hook. They reported that the issue went away after a few minutes. Where should the voice systems administrator begin troubleshooting?
A. SIP gateway
B. Cisco Unified Communications Manager subscriber ***
C. Network cable
D. 7945 IP phone

QUESTION 22
What allows a phone user to log a phone out of all line groups to which the phone directory numbers belong?
A. Cisco IPPA
B. Cisco Finesse
C. HLog softkey ***
D. Cisco Agent Desktop

QUESTION 23
When you configure a shared extension in Cisco Configuration Professional, which two characteristics should be the same on both phones, so that the phones can successfully use a shared extension? (Choose two.)
A. Monitor mode
B. MAC address
C. Ephone-dn ***
D. Number ***
E. User ID

QUESTION 24
Which call processing agent is based on Cisco IOS software and works with ISR platforms?
A. Cisco Unified Presence Server
B. Cisco Unity Connection
C. Cisco Unified Communications Manager Express ***
D. Cisco Unified Communications Manager
E. Cisco UnifiedContact Center Express

QUESTION 25
Which two fields are required parameters when manually creating users on Cisco Unity Connection with predefined templates? (Choose two.)
A. Username (alias) ***
B. Extension ***
C. First name and last name
D. Employee ID
E. Title

QUESTION 26
Which service allows the network to provide better or special services to a set of users and applications at the expense of other users and applications?
A. QoS ***
B. Dial plans
C. Route patterns
D. Dial peers

QUESTION 27
Which two options allow the maximum message length to be adjusted in Cisco Unity Connection? (Choose two.)
A. Message Settings under individual users ***
B. User Templates > VoiceMailUserTemplate > Message Settings ***
C. Contacts > Message Settings
D. Enterprise Parameters > Maximum Message length
E. Service Parameters > Voicemail Settings

QUESTION 28
An end user reports that they are unable to control their Cisco IP phone using Cisco Unified Personal Communicator and cannot make any calls. Which situation can cause this issue?
A. The Cisco Unified Personal Communicator is not registered in the Cisco Unified Presence server.
B. The LDAP integration is incorrect.
C. The Cisco Unified Personal Communicator is configured in desk-phone mode.
D. The Allow Control of Device from CTI checkbox in the device configuration on Cisco Unified Communications Manager is disabled. ***
E. The Allow Control of Device from CTI checkbox in the device configuration on the Cisco Unified Presence is disabled.

QUESTION 29
Can an IP phone be configured so that calls to that IP phone can be rerouted if the IP phone become unregistered?
A. Yes, configuring call forward All provides this coverage
B. No, if a phone is unregistered, the re-order tone is played to the caller
C. Yes, configuring Call Forward Busy Internal provides this coverage
D. Yes, configuring Call Forward Unregistered provides this coverage ***
E. No, the call is dropped at the gateway

QUESTION 30
which two password options are there to set up voicemail
A. Does not expire ***
b. user must change at next login ***
?????
?????

QUESTION 31
A network engineer mUst perform a manual back up of cucm which or where can he do this
A. disaster recovery sys ***
?????
?????
?????

QUESTION 32
A network engineer wants to delete unassigned phone extensions from cucm where can he ???
A. Route plan report ***
B. route plan details
?????
?????

QUESTION 33
An admin is settin up a remote site in cucm manager that has a T1 wan connection to the main site which option is a better voip codec for the site
A. g729 ***
B. g711
C. g712
D. g723

QUESTION 34
which two actions can be selected with bulk admin tool in cisco unity connection
A. create ***
B. delete ***
C. import
D. ??????

QUESTION 35
what to use when importing many users to cisco unity connection.
A. bulk admin ***
B. cobras
??????
??????

QUESTION 36
an engineer is creating a new phone what option appears first
A. phone type ***
B. mac adress
??????
??????

QUESTION 37
A customer has requested that all employees have standard cti enabled and standard ccm roles how would this be assigned to?
A. access control group ***
??????

QUESTION 38
Where can you dwonload the rtmt app in cucm
A. cucm administator ***
B. cucm os
C. cucm plugin manager
D. ??????

QUESTION 39
Ip phone user report that the mwi light does not work while receiving vm message which action must be taken to trouble shoot in unity connection
A. run port activity report ***
B. reset the phone
C. reset mwi fn in unity connection
D. check user mailbox

QUESTION 40
Which option would an administrator use to find all unassigned directory numbers in Cisco Unified Communications Manager?
A. Route plan report ***
B. CDR
C. CAR
D. Cisco Reporting Tool
E. Directory number lookup

QUESTION 41
Which menu does a voice engineer use to create a phone user account in the Cisco Unified CME GUI?
A. Configure ***
B. Voicemail
C. Administration
D. Reports

QUESTION 42
Which transport layer protocol is used when a Cisco Unified Presence client is searching for a contact in directory?
A. TCP ***
B. UDP
C. IMAP
D. http

QUESTION 43
Which options are two on-premise components of Cisco Unified Presence? (Choose two.)
A. Cisco Unified Communication Manager ***
B. Cisco Unified Contact Center Express
C. Cisco WebEx ***
D. Cisco Quality Management
E. Cisco Unified Contact Center Enterprise

QUESTION 44
Customer requirements dictate that local calls from area code 408 display the ANI as a 7-digit number. Which procedure allows the leading digits to be stripped as soon as they arrive at the H.323 voice gateway?
A. Set up a voice translation rule, apply the translation rule to a translation profile, and apply the translation profile to the dial peer in the inbound direction. ***
B. Set up a voice translation profile, apply the translation profile to a translation rule, and apply the translation rule to the dial peer in the outbound direction.
C. Set up a voice translation rule, apply the translation rule to a translation profile, and apply the translation profile to the dial peer in the outbound direction.
D. Set up a voice translation profile, apply the translation profile to a translation rule, and apply the translation rule to the dial peer in the inbound direction.

QUESTION 45
An engineer is syncing Cisco Unity Connection with LDAP. Which two things should the engineer consider during this process? (Choose TWO.)
A. PINs and passwords are replicated from the LDAP database to Cisco Unity Connection database.
B. LDAP authentication must be configured and enabled.
C. There is no limit to the amount of LDAP filters that can be created. ***
D. SSL certificates from LDAP must be uploaded to Cisco Unity Connection.
E. LDAP synchronization must be configured and enabled. ***
F. Cisco Unity Connection supports integrations with OpenLDAP.

QUESTION 46
In which section of Cisco Unified Communications Manager are Call Detail Records viewed?
A. Cisco Unified Serviceability ***
B. Cisco Unified OS Administration
C. Cisco Unified Reporting
D. Cisco Unified Communications Manager Administration
E. Cisco Unified Disaster Recovery

QUESTION 47
In an effort to proactively manage IP telephony infrastructure, a network engineer wants to review usage reports that provide top five users, top five calls, and traffic summary. Which option describes where this information can be retrieved using Cisco Unified Communications Manager?
A. Navigate to Cisco Unified CM Administration > CDR Analysis and Reporting >System Reports > System Overview > Select desired reports.
B. Navigate to Cisco Unified Operating System Administration > Tools > System Reports > System Overview > Select desired reports.
C. Navigate to Cisco Unified Serviceability > Tools > CDR Analysis and Reporting > System Reports > System Overview > Select desired reports. ***
D. Navigate to Cisco Unified Reporting > Tools > System Reports > System Overview > Select desired reports.

QUESTION 50
A user reports that several IP phones in a single department are displaying a continuous “registering” message. Which fault domain should be investigated?
A. network router
B. Cisco Unified Communications Manager subscriber node
C. network switch ***
D. IP phones
E. SIP gateway

QUESTION 51
An engineer is adding four cordless analog phones to Cisco Unified Communications Manager. Which solution best meets this requirement?
A. Cisco VG202 Analog Voice Gateway
B. Cisco VG204 Analog Voice Gateway ***
C. Cisco VG224 Analog Voice Gateway
D. Cisco VG350 Analog Voice Gateway

QUESTION 52
User A needs to have a line shared on the user B phone. Both phones register with Cisco Unified Communications Manager. Which method can be used from Cisco Unified Communications Manager Administration web pages to configure a shared line on the user B phone?
A. Navigate to the user B phone > Add the user A DN. ***
B. Navigate to the user B phone > Shared Line > Add the user A DN.
C. Navigate to DN configuration > Shared Line > Add the user A DN.
D. Navigate to end user configuration > Shared Line > Add the user A DN.

QUESTION 53
Which two profile types are needed to enable a user for IM and Presence? (Choose two.)
A. Cisco Unified Communications Service ***
B. voicemail profile
C. Jabber profile
D. device profile
E. network access profile
F. service profile ***

QUESTION 54
An engineer is adding user accounts to Cisco Unity Connection and needs to limit the maximum length of messages. Which aspect defines this limit when adding new accounts?
A. user templates
B. user partitions and search spaces
C. user CoS ***
D. user mailbox store
E. user roles

QUESTION 55
How many servers can be supported in a Cisco Unified IM&Presence Server cluster environment?
A. 2
B. 4
C. 6 ***
D. 8
E. 10

QUESTION 56
A Cisco Unified Communications administrator wants to implement Cisco IM and Presence for the company. If it is installed in IM-only user mode, which three services are supported for users? (Choose three.)
A. video calls support
B. third-party XMPP client support ***
*C. presence support
D. Microsoft Lync support
E. Microsoft Office Communicator support
F. instant messaging support ***

QUESTION 57
A user needs to access CAR logs to adjust settings. Which two options are required? (Choose two.)
A. The user account has the Standard CAR Admin Users role. ***
B. The user must log in at https://:8443/car/Logon.jsp. ***
C. The user must log in at https://:8443/cdr/Logon.jsp.
D. The user account has the CTI Enabled role.
E. The user account has the Standard CAR role.

QUESTION 58
On the PSTN gateway, a network engineer runs sh isdn status and finds the Layer 2 state of each interface to be “TEI_ASSIGNED”. What is the status of PSTN connectivity from this gateway?
A. The T1 interfaces are established and operational.
B. This information does not indicate the status of PSTN connectivity from the gateway.
C. The T1 interfaces are down. ***
D. The T1 interfaces are being tested by the carrier.

QUESTION 59
Which command is useful to see if network layer information is being received at a PSTN gateway?
A. Show gateway status
B. Show isdn q931
C. Show c cm-manager status
D. Show isdn status ***
E. Show isdn q921

QUESTION 60
Which three rules are valid transfer rules in Cisco Unity Connection? (Choose three.)
A. Standard ***
B. Alternate ***
C. Closed ***
D. Holiday
E. Nonstandard

QUESTION 61
A user in Cisco Unified Communications Manager Administration has been added to the Standard CCM Admin Users group, which includes the Standard CCMADMIN Administration role, but the user cannot add new users. What is the cause of this issue?
A. The add user capability has been disabled for the group
B. The incorrect group and role were assigned. ***
C. The add user capability has been disabled for the role.
D. Only the CCMAdmin user can add users.
E. Users can be added only via LDAP

QUESTION 62
If the latency is 250ms for voice (IP phone) how the user will be effected?
A. Enterprise VoIP networks tend to have a looser target—250 ms (a decent limit: 220 ms without propagation).
B. delay and interruption ***
C. call is dropped
D. voice quality cuts in and out

QUESTION 63
Which protocol is used to robbed bytes?
A. CAS ***
B. CSS
C. SIP
D. SCCP

QUESTION 64
What is the amount of jitter in milliseconds used for voice?
A. 30 ***
B. 40
C. 50
D. 60

QUESTION 65
How to add a conference Q bridge to phone in phone configuration page?
A. Media resource group list = MRGL ***
B ???
C ???
D ???

QUESTION 66
Phone connects to a switch. Which three options are sent by the DHCP server?
A. IP Address ***
B. Default-Gateway ***
C. TFTP ***
D ???
E ???

QUESTION 67
MWI is not lighting when there is an incoming message. How to troubleshoot?
A. Restart phone.
B. Mailbox is full.
C. Check MWI function in CUC ***
D. Run port activity report ****
E ???

Answer: C or D ???

QUESTION 68
When you change the security profile for a phone in CUCM, what happens:
A. Rebuild The .xml file of the phone ***
B. ???
C. ???
D. ???

QUESTION 69
Which scenario allows user A in partition X to call user B in Cisco Unified Communications Manager?
A. User B in partition X is not assigned to any CSS.
B. User B in partition Y assigns both partitions to CSS-X.
C. User B is not assigned to any partition or CSS. ***
D. User B is assigned to partition Y and assigns to CSS-X.

QUESTION 70
How many phone can be registered on the standard cluster?
A. 30k
B. 35k
C. 40k ***
D. 45k

QUESTION 71
Which of the following can not be displayed by using the CAR System Reports menu? Choose 2?
A.Malicious call details
B.The current number of billing errors
C.The call volume for a given period of time
D.QoS rating information for inbound calls
E.Route and Line group utilization information ***
F.The top number of users by maximum length of calls ***

QUESTION 72
Which of the following can you display by clicking System Reports> Traffic> Summary by Phone Number in the UCM 8.0 CAR GUI?
A.The QoS rating information for inbound calls
B.The current number of billing errors
C.The call volume for a given period of time ***
D.The top number of users by maximum length of calls

QUESTION 73
Where to find concurrent and dropped calls?
A. Serviceability
B. RTMT ***
C. Reporting
D ???
E ???

QUESTION 74
How fast can Cisco Unified Communications Manager generate CDR and CMR files?
A. One CDR file and one CMR file every minute for up to 1 hour ***
B. One CDR file and one CMR file every second for up to 1 minute
C. Ten CDR files and ten CMR files every hour for up to 1 day
D. Ten CDR files and ten CMR files every day for up to 1 week

QUESTION 75
With which of the following control components of UCM media resources interact when UCM needs to locate resources to establish a conference call?
A. Media control
B. MOH control
C. MTP control
D. Call control ***

QUESTION 76
With which of the following control components of UCM media resources interact when UCM needs to locate resources to establish transcoding?
A. Media control ***
B. Call control
C. MTP control
D. MOH control

QUESTION 77
Which of the following UCM services enables the use of Cisco Unified Personal Communicator in softphone mode when integrating CUPS server with UCM?
A. Cisco Call Manager
B. Cisco TFTP ***
C. Cisco AXL Web Serbice
D. Cisco CTI Manager

QUESTION 78
A customer has requested that all employees have standard cti enabled and standard ccm roles how would this be assigned to?
A.access control group ***
B. ???
C. ???
D. ???

QUESTION 79
An engineer must ensure that user data is maintained in lightweight directory access protocol and copied to Cisco Unity Connection, but Cisco Unity Connection-specific data is locally maintained in the Cisco Unity Connection database. Which user creation option accomplishes this task?
A. Bulk administration
B. Import from CUCM via AXL
C. Import from LDAP ***
D. Manual creation

QUESTION 80
Under phone configuration what option is used to add conference bridges?
A. Media resource group list ***
B. ???
C. ???
D. ???

QUESTION 81
Where can you dwonload the rtmt app in cucm
A. cucm ***
B. cucm os
C. cucm plugin manager

QUESTION 82
You are the administrator for your company´s UCM network. Your company is running the UCM 8.6(1). Examine the exhibit below, and answer the associated question:
Which of the following is not a step you might take to troubleshoot the error in this scenario?
A. Click User Management > User settings > Service Profile in UCM Administration ***
B. Click User Management > End User in UCM Administration
C. Click Advanced Settings on the Cisco Jabber login page
D. Click Application > CUPC/Cisco Jabber in CUPS Administration

QUESTION 83
Which of the following is not true of both CUPS persistent chat rooms and CUPS ad-hoc chat rooms?
A. The presence status of users cannot be viewed and an ad-hoc room.
B. Users cannot invite other users to persistent room
C. Both rooms are deleted when the last user logs out
D. Ad-hoc chat rooms allow the recording of transcripts.
E. Neither room can be created or managed by users ***

QUESTION 84
Which of the following interfaces handles the exchange of availability information between third-party clients and a Cisco Presence deployment?
A. SIP
B. LDAP
C. AXL/SOAP
D. XMPP ***

QUESTION 85
Which of the following can you display by clicking System Reports in the CAR GUI? Select 4 choices
A. The call volume for a given period of time ***
B. Malicious call details ***
C. QoS rating information for inbound calls ***
D. The current number of biling errors ***
E. The top number of users my maximum length of calls
F. Route and line group utilization

QUESTION 86
Which of the following can you display by clicking User Report > Top NUMBER in the UCM 8.0 CAR GUI?
A. The top QoS rating information for inbound calls
B. The top call volume for a given period of time
C. The top number of users by maximum length of calls ***
D. The top number of billing errors

QUESTION 87
Which of the following is not information that is available by clicking Tools > System Reports > System Overview in Cisco Unified Serviceability? Choose two
A. Top five users based on duration
B. Top five calls based on duration
C. Top five destinations based on charge
D. Top five calls based on volume ***
E. Top five sers based on volume ***
F. Top five users based on charge

QUESTION 88
Which of the following enables an administrator to view reports and manage UCM features?
A. Unified Reporting
B. Unified Serviceabiity ***
C. RTMT
D. CAR

QUESTION 89
Which of the following can you display by clicking System Reports > CDR Error in the UCM 8.0 CAR GUI?
A. Top number of users by maximum length of calls.
B. QoS rating information for inbound calls
C. Malicious call details
D. The current number of billing errors ***
E. The call volume for a given period of time
F. Route and Line Group Utilization information

QUESTION 90
A user informs you that CAR queries are failing consistently for recent dates. However, older dates are still accessible. Which of the following is most likely the problem?
A. The disk space where reports are stored is full
B. The user does not have the privileges to log on to CAR
C. The Cisco CAR Web Service is not running
D. The CDR Enable Flag is set to FALSE ***
E. The UCM System is generating CDR files too slowly

QUESTION 91
Which of the following is true of the Cisco Unified Serviceability System Overview report?
A. It does not contain traffic summary reports
B. It is only available to CAR administrators ***
C. It cannot contain a complete set of system reports
D. It can only be generated automatically

QUESTION 92
Which of the following can a user template automaticaly configure for a new user in Unity Connection? Choose 2
A. An administratr role ***
B. The message volume ***
C. And SMTP address
D. An extension number
E. A user alias

QUESTION 93
Which of the following reports can be displayed by using the CAR Device Reports menu?
A. QoS rating information for inbound calls
B. Malicious call details
C. Route and Line Group utilization information ***
D. The call volume for a given period of time
E. The current number of billing errors
F. The top number of users by maximum length of calls

QUESTION 94
Which of the following is not available from the Service Statistics Report in Cisco Unified Serviceability?
A. The number of TFTP requests
B. The number of open CTI lines
C. The number of registered phones per server ***
D. The number of aborted TFTP requests

QUESTION 95
Which of the following interfaces enables database synchronization between UCM and CUPS server?
A. AXL/SOAP ***
B. XMPP
C. LDAP
D. SIP

QUESTION 96
You want to enable a user to acess Cisco Unity Connection voice mail by using IMAP. Which of the following should you modify?
A. The users´ CoS configuration ***
B. The users´ interview handler configuration
C. The Exchange message store configuration
D. The users´account configuration

QUESTION 97
You assign a UCM user to the Standard CAR Admin Users Group in UCM. However, the user reports that CAR cannot be accessed from the tools menu in Cisco Unified Serviceability. Which of the following is most likely the cause of the problem?
A. The Cisco CAR web Service is not running ***
B. The disk space where reports are stored is full
C. The user does not have the privileges to access CAR
D. The UCM system is generating CDR files too slowly
E. The CDR Enabled Flag is set to FALSE

QUESTION 98
Which of the following is available from the Service Statistics Report in Cisco Unified Serviceability?
A. The number of open CTI lines ****
B. The number of registered phones per server
C. The number of phones in the cluster
D. The number of H.323 gateways in the cluster

QUESTION 99
Which of the following can administraros display by clicking Device Reports > Gateway in the CARU GUI?
A. The Gateway detail report
B. Any of the gateway device reports ***
C. The gateway utilizaion report
D. The gateway summary report

QUESTION 100
Which of the following does not provide access to realtime reporting?
A. CAR ***
B. RTMT
C. Unified Serviceability
D. Unified Reporting

QUESTION 101
Which of the following interfaces handles the exchange of availability information between UCM and CUPS?
A. XMPP
B. AXL/SOAP
C. LDAP
D. SIP ***

QUESTION 102
you are migrating users from CUCM UDS to CUC which template would you use to do this?
A. User template ***
B ???
C ???
D ???

QUESTION 103
Troubleshooting MWI issue :
A. Reset MWI in Unity ***
B. ???
C. ???
D. ???

QUESTION 104
on-premises IM presence
A. CUCM **
B. CUC **
C. ???
D. ???

QUESTION 105
If the users are complaining bad voice quality, where’s the first step to troubleshoot ?
A. Router ***
B. Switch ***
C. ???
D. ???

QUESTION 106
A network engineer mst perform a manual back up of cucm which or where can he do this
A. disaster recovery system ***
B. ???
C. ???
D. ???

QUESTION 107
Advantage of QoS
A. avoid congestion ***
B. minimizes priority
C. supports dedicated bandwidth ***
D. improved loss characteristics ***

QUESTION 108
Protocol which IMP uses to access directory
A. tcp ***
B. ???
C. ???
D. ???

QUESTION 109
Two Components of IM and presence
A. cucm ***
B. cuc ***
C. cisco quality mgmt??
D. uccx
E. ucce

QUESTION 110
Monitor call quality
A. RTCP
B. ???
C. ???
D. ???

QUESTION 111
Where to config message length in CUC?
A. COS
B. ???
C. ???
D. ???

QUESTION 112
How to add a second line in CME
A. ephone-dn 1 dual-line ***
B. ???
C. ???
D. ???

QUESTION 113
Something about how MGCP is routed
A. route pattern ***
B. translation rule
C. static route
D. ???

QUESTION 114
T1 CAS steals bits from the voice channel to transfer signaling information
A. CAS ***
B. ???
C. ???
D. ???

QUESTION 115
Which options are two on premise components of cisco unified presence.
A. CUCM
B. Unity Connection
C. ???
D. ???

QUESTION 116
When you delete a voicemail in Unity Connection, how many days is it kept in the “Deleted” folder before it gets automatically erased:
A. 15 ***
B. 30
C. 60
D. 90

QUESTION 117
If shared mailbox for multiple users. Choose 2 password settings
A. no password
B. cannot change password ***
C. password is locked by admin
D. change password after first login
E. password will not expire ***

QUESTION 118
How can you reset a voicemail PIN for a LDAP User in Unity:
A. Change password ***
B. Password settings ***
C. ???
D. ???

QUESTION 119
How to create a report regarding congestion:
A. traffic
B. ???
C. ???
D. ???

QUESTION 120
who can modify recorded messages?
A. greeting administrator ***
B. ???
C. ???
D. ???

the question and answer back at page 72 is for 210-065 or 210-060? I thought it is 210-065?

@Luka

QUESTION 1: Which two technologies comprise a Cisco Presence deployment? (Choose two.)

A. Cisco Unified Presence Server
B. Cisco Unity Connection
C. Cisco Unified Communications Manager
D. Active Directory
E. Cisco Unified Border Element
F. Cisco Expressway

Answer: AC

Note:
The Cisco IM and Presence Service must be deployed with the equivalent version of Cisco Unified Communications Manager (Unified CM)

On-Premises Cisco IM and Presence Components
Cisco IM and Presence Service
Cisco Unified Communications Manager (Unified CM)
Cisco Jabber
Cisco Unity Connection
Lightweight Directory Access Protocol (LDAP) Server v3.0
Cisco Collaboration voice and video endpoints
Third-party presence server
Third-party XMPP clients
Third-party applications

Finally passed my 210-060 exam, I got the 210-060 PDF from braindumpscerts.com & very happy with their updated exam study material. I got almost 90% same questions on my real exam which I already prepared from 210-060 PDF. Big thanks to the team

Hello friends!. I’m Salvador from Mexico and I passed the 210-065 exam with the DUMP VCE / PDF. To recover my money I can send them by mail for only 10 $ Dollar.

I left the link from PAYPAL and my email to write to me and then I sent them the exam.

Good luck

NOTE: Delete the spaces:

h t t p s : / / p a y p a l . m e / t h n k d o n a t i o n s
i n g . s p i n e d a @ g m a i l . c o m

210-065 – Implementing Cisco Video Network Devices (CIVND) – 390 Q & As

Thank Patricia, i passed since few minutes using your dumps

Awesome materials and dumps

Thanks Patricia
Passed too today 985 /1000

@ALL STOP SPAMMING !!!!!!!

@Kris and Help 210-060, Anonymous: please confirm, once again, the right CICD answers:

Q69: Which scenario allows user A in partition X to call user B in Cisco Unified Communications Manager?

A. User B in partition X is not assigned to any CSS.
B. User B in partition Y assigns both partitions to CSS-X.
C. User B is not assigned to any partition or CSS.
D. User B is assigned to partition Y and assigns to CSS-X.

Q15. An engineer must ensure that user data is maintained in lightweight directory access protocol and copied to Cisco Unity Connection, but Cisco Unity Connection-specific data is locally maintained in the Cisco Unity Connection database. Which user creation option accomplishes this task?

A. Bulk administration
B. Import from CUCM via AXL
C. Import from LDAP
D. Manual creation

Q189. A user in Cisco Unified Communications Manager Administration has been added to the Standard CCM Admin Users group, which includes the Standard CCMADMIN Administration role, but the user cannot add new users. What is the cause of this issue?

A. The add user capability has been disabled for the group
B. The incorrect group and role were assigned.
C. The add user capability has been disabled for the role.
D. Only the CCMAdmin user can add users.
E. Users can be added only via LDAP

Q234. A manager is generating bill reports for a particular user. Which navigation sequence must be used for this task?

A. Bills > Department
B. User Reports > Bills > Department
C. Bill > Individual
D. User Reports > Bills > Individual

Q227. An administrator must keep CDR data for a longer period of time and wants to modify the configured value of the CDR/CMR Files Presentation Duration Days). Which menu options does the engineer navigate?

A. Unified CM Administration > System > Enterprise Parameters
B. Unified Serviceability > Tools > Serviceability Reports Archive
C. Unified CM Administration > Call Routing > Route Plan Report
D. Unified Serviceability > Tools > CDR Management

@Kris, @Help 210-060, @Anonymous, there are two similar CICD questions:

Q1. Which options are two on-premise components of Cisco Unified Presence? (Choose two).

A. Cisco Unified Communication Manager
B. Cisco Unity Connection
C. Cisco Quality Management
D. Cisco Unified Contact Center Express
E. Cisco Unified Contact Center Enterprise

Q44. Which options are two on-premise components of Cisco Unified Presence? (Choose two).

A. Cisco Unified Communication Manager
B. Cisco Unified Contact Center Express
C. Cisco WebEx
D. Cisco Quality Management
E. Cisco Unified Contact Center Enterprise

– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————More questions from @Sven by email
A question about GLBP – uses UDP 3222
—————————————————————————————————
Anyone else who has passed can remember the choices to these questions?
– Another with the aaa authentication with radius and local db as backup if RADIUS was unavailable.
– Two ways a port can respond to port-security
——————————————————————
D&D – GLBP (AVG/AVF/Gateway Priority/ARP)
– AVG – assigns virtual MAC addresses.
– AVF – forwards packets to virtual MAC.
– Gateway Priority – determines who is the AVG.
– ARP – ??? <<<can anyone remember this option as well?
——————————————————————
D&D – RADIUS/TACACS+
RADIUS
– Combining the AAA function
– ??? <<<can anyone remember this option as well?
– ??? <<<can anyone remember this option as well?
TACACS+
– Encryption of the whole header
– Separating the AAA functions
– TCP port 49
—————————————————————

A. User B in partition X is not assigned to any CSS.
B. User B in partition Y assigns both partitions to CSS-X.
C. User B is not assigned to any partition or CSS.
D. User B is assigned to partition Y and assigns to CSS-X.

Q15. An engineer must ensure that user data is maintained in lightweight directory access protocol and copied to Cisco Unity Connection, but Cisco Unity Connection-specific data is locally maintained in the Cisco Unity Connection database. Which user creation option accomplishes this task?

A. Bulk administration
B. Import from CUCM via AXL
C. Import from LDAP
D. Manual creation

Q189. A user in Cisco Unified Communications Manager Administration has been added to the Standard CCM Admin Users group, which includes the Standard CCMADMIN Administration role, but the user cannot add new users. What is the cause of this issue?

A. The add user capability has been disabled for the group
B. The incorrect group and role were assigned.
C. The add user capability has been disabled for the role.
D. Only the CCMAdmin user can add users.
E. Users can be added only via LDAP

Q234. A manager is generating bill reports for a particular user. Which navigation sequence must be used for this task?

A. Bills > Department
B. User Reports > Bills > Department
C. Bill > Individual
D. User Reports > Bills > Individual

Q227. An administrator must keep CDR data for a longer period of time and wants to modify the configured value of the CDR/CMR Files Presentation Duration Days). Which menu options does the engineer navigate?

A. Unified CM Administration > System > Enterprise Parameters
B. Unified Serviceability > Tools > Serviceability Reports Archive
C. Unified CM Administration > Call Routing > Route Plan Report

3

can any one help for below ? any news for 210-065 ?

2.TP immersive system installation prepare checks
A) avoid high contrast ambient
B) avoid glossy surfaces
C) avoid decoration and plants
D) use earth colour palette

@Khaled,
What source you have this question?

Answers: AB (in my opinion)

Check page 57 – table “Decor to avoid”
https://www.cisco.com/c/dam/en/us/solutions/collateral/collaboration-endpoints/c07-643449-00_tp_dg.pdf

@johnson

thank u , actually i’m confuse about it… did you take the Exam 065 or preparing.

…preparing, but day by day feel more confident.

A technician is trying to troubleshoot real-time call information from the CLI of a VCS. Which command should the technician enter?
A. xstatus
B. xconfiguration
C. xfeedback
D. xhistory
E. xcommand

Answer: some dumps says A which is incorrect, correct one is C

anyone passed recently 210-065? please share dumps

@Khaled
@johnson
hi khaled and johnson
can we contact for help ?
i preparing also to take 210-065 exam
islameng2014 at gmail dot com

@johnson
yes C is correct

One of the questions on 210-065

Configure 2min unlock time for admin account CUCM
A. set accountlocking unlocktime 2
B. set accountlocking unlocktime 120
C. set accountlocking unlocktime cost 2
D. set accountlocking unlocktime cost 120

B is correct

Source: https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/cli_ref/8_6_1/cli_ref_861.html

@ johnson thank you man ,
If you have any new Q please share it with us.

@Islam
yes sure we can

CICD 210-060 please can anyone point where Can I find the dumps or valid exams questions
we use to share in this site not..

please I need the info

tres23411 @ gmail . com

If anybody can help me with the dumps
please send it here tres23411 @ gmail . com if you can

Mark you know what you can do where your post …
I don’t nee to tell you

Mark you know what you can do with your post right
Stop being what you are …

finally cleared the 210-060 exam by learning the 210-060 PDF got from braindumpscerts.com almost 95% questions are the same on the real exam. thanks much to the team.

Thank you mark

Awesome test simulator

what is the correct answer ?

QUESTION 292 XConfigurator Cameras Camera 1 Brightness Level 1 command has not effect. Why?
A. brightness mode must be set to manual
B. codec must be rebooted for the changes to take effect
C. display brightness was changed for the remote end
D. default brightness level is 1
Answer: A or B

QUESTION 304 I releave a value of acoustic 25 db at a distance of 1 feet. What am I measuring?
A. NC
B. SPL
C. direct ambient reflection
D. STC E. local resonance
Answer: C or B

@Luka, this is in my opinion

Q69: Which scenario allows user A in partition X to call user B in Cisco Unified Communications Manager?
A. User B in partition X is not assigned to any CSS.
B. User B in partition Y assigns both partitions to CSS-X.
C. User B is not assigned to any partition or CSS.
D. User B is assigned to partition Y and assigns to CSS-X.
Answer: C
Q15. An engineer must ensure that user data is maintained in lightweight directory access protocol and copied to Cisco Unity Connection, but Cisco Unity Connection-specific data is locally maintained in the Cisco Unity Connection database. Which user creation option accomplishes this task?
A. Bulk administration
B. Import from CUCM via AXL
C. Import from LDAP
D. Manual creation
Answer: A
Q189. A user in Cisco Unified Communications Manager Administration has been added to the Standard CCM Admin Users group, which includes the Standard CCMADMIN Administration role, but the user cannot add new users. What is the cause of this issue?
A. The add user capability has been disabled for the group
B. The incorrect group and role were assigned.
C. The add user capability has been disabled for the role.
D. Only the CCMAdmin user can add users.
E. Users can be added only via LDAP
Answer: B
Q234. A manager is generating bill reports for a particular user. Which navigation sequence must be used for this task?
A. Bills > Department
B. User Reports > Bills > Department
C. Bill > Individual
D. User Reports > Bills > Individual
Answer: C
Q227. An administrator must keep CDR data for a longer period of time and wants to modify the configured value of the CDR/CMR Files Presentation Duration Days). Which menu options does the engineer navigate?
A. Unified CM Administration > System > Enterprise Parameters
B. Unified Serviceability > Tools > Serviceability Reports Archive
C. Unified CM Administration > Call Routing > Route Plan Report
D. Unified Serviceability > Tools > CDR Management
Answer: D
Q1. Which options are two on-premise components of Cisco Unified Presence? (Choose two).
A. Cisco Unified Communication Manager
B. Cisco Unity Connection
C. Cisco Quality Management
D. Cisco Unified Contact Center Express
E. Cisco Unified Contact Center Enterprise
Answer: AB
Q44. Which options are two on-premise components of Cisco Unified Presence? (Choose two).
A. Cisco Unified Communication Manager
B. Cisco Unified Contact Center Express
C. Cisco WebEx
D. Cisco Quality Management
E. Cisco Unified Contact Center Enterprise
Answer: AC

what is the correct answer ?

@Khaled,

In my research, the answer is A

QUESTION 292 XConfigurator Cameras Camera 1 Brightness Level 1 command has not effect. Why?
A. brightness mode must be set to manual
B. codec must be rebooted for the changes to take effect
C. display brightness was changed for the remote end
D. default brightness level is 1
Answer: A or B

QUESTION 304 I releave a value of acoustic 25 db at a distance of 1 feet. What am I measuring?
A. NC
B. SPL
C. direct ambient reflection
D. STC E. local resonance
Answer: C or B

@Khaled…for me B

@GC12
Answer is B

Another questions from test:

What is threshold % for CTCS when it cant store more recordings?
A. 75%
B. 80%
C. 95%
D. 98%

@Pit

The answer is D i believe for below question

What is threshold % for CTCS when it cant store more recordings?
A. 75%
B. 80%
C. 95%
D. 98%

Hi All,

Anybody who met this question in the exam?

The Cisco Telepresence Codec C90 is unable to call the Cisco IP Video Phone. Assuming that the calling search space has been configured correctly, which of the these can cause this issue?
A. The Cisco Telepresence Codec C90 can only be registered to a Cisco Telepresence Video Communication Server.
B. A multipoint control unit is required in order for the call to work.
C. The Cisco Telepresence Codec C90 can only be registered as a SIP endpoint to Cisco Unified Communications Manager. H.323 is not supported.
D. URI dialing has not been configured on Cisco Unified Communications Manager.
E. The Cisco Telepresence Codec C90 Profile 1 > CallSetupMode must be configured as a gateway since Cisco Unified Communications Manager does not have a gatekeeper functionality.
F. The Cisco Telepresence Codec C90 is not registered as a SIP endpoint on Cisco Unified Communications Manager.
The Cisco Telepresence Codec C90 needs to be registered as both SIP and G.323.

Also this

Which three features are supported by the Cisco Video Surveillance Encoding Server? (Choose three.)
A. IP and analog cameras
B. MPEG-2 and MPEG-4 encoding
C. archiving
D. motion detection
E. clustering
F. virtual matrix

@GC12 thank you , could you please help for below also;

Which three features are supported by the Cisco Video Surveillance Encoding Server? (Choose
three.)
A. IP and analog cameras
B. MPEG-2 and MPEG-4 encoding
C. archiving
D. motion detection
E. clustering
F. virtual matrix

@Khaled, i think the answer is ACD.

Brothers who knows the correct answer, please confirm if i am correct.

@GC12

The Cisco Telepresence Codec C90 is unable to call the Cisco IP Video Phone. Assuming that the calling search space has been configured correctly, which of the these can cause this issue?
A. The Cisco Telepresence Codec C90 can only be registered to a Cisco Telepresence Video Communication Server.
B. A multipoint control unit is required in order for the call to work.
C. The Cisco Telepresence Codec C90 can only be registered as a SIP endpoint to Cisco Unified Communications Manager. H.323 is not supported.
D. URI dialing has not been configured on Cisco Unified Communications Manager.
E. The Cisco Telepresence Codec C90 Profile 1 > CallSetupMode must be configured as a gateway since Cisco Unified Communications Manager does not have a gatekeeper functionality.
F. The Cisco Telepresence Codec C90 is not registered as a SIP endpoint on Cisco Unified Communications Manager.
The Cisco Telepresence Codec C90 needs to be registered as both SIP and G.323.

I think the ans is (C)

any idea:

2.TP immersive system installation prepare checks
A) avoid high contrast ambient
B) avoid glossy surfaces
C) avoid decoration and plants
D) use earth colour palette

@Khaled

For me AC…when are you taking the exam?

A – CORRECT
Quote:
“… of high contrast that are difficult for video to process.”

B – CORRECT
Quote:
“Light reflections in an Immersive Cisco TelePresence environment should be controlled such that
they do not reflect light into the cameras or on displays to avoid issues such as glare, lens flares, or
undesirable points of interest in the room that distract from participants being the focal point. ”

C – WRONG
Quote:
“Adding furniture, plants, wall hangings, and other décor to a room can also significantly reduce reverberation in a
room. Any items that provide additional reflection and absorption of sound reduce overall reverberation.”

D – WRONG
Quote:
“Dark furniture tends to create numerous areas of high contrast that are difficult for video to process.”

@GC12

QUESTION 362
Which two UDP services are available on an MCU? (Choose two.)

A. FTP
B. HTTP
C. SNMP
D. encrypted SIP
E. H.323 gatekeeper

Answer: CE
——–

i planning to have the exam next week bro.

@ thank you Pit

if you have any new Q’s please share it with us.

@Khaled
I’m taking the exam too after 2 weeks

@Pit
Thanks bro for the input…appreciate if you could share new questions in the exam

any Idea

8) Which are udp connection in “VCS”?
A) http
B) ftp
C) secure sip
D) snmp
E) forgot
===========================
Which two UDP services are available on an MCU? (Choose two.)

A. FTP
B. HTTP
C. SNMP
D. encrypted SIP
E. H.323 gatekeeper
===================================
Which of these are cisco media player models? Choose two

Edge 300
Edge 340
Cisco MXE
Cisco Cast
=======================================
EX60 troubleshooting question: AUDIO is fine but no video.Where do you start to troubleshoot?
================================================================
5) EX90 outbound calls ok, inbound calls KO troubleshoot.Where to start( something like that)

@Khaled
are you using dumps from Chule or PL?

@GC12

yes I have Chule and another one but look like the same

just I review the pages here and I notice some new Q’s without answer.

@Khaled

pls send me message echocruz12 at gmail dot com

@Khaled
Regarding MCU UDP Services, SNMP is UDP and there is stated in cisco docs that mcu uses H323 RAS for outbound which is udp also and is used for communication with GK.

can we have a group for folks planning for 210-065?

A technician is trying to troubleshoot real-time call information from the CLI of a VCS. Which command should the technician enter?
A. xstatus
B. xconfiguration
C. xfeedback
D. xhistory
E. xcommand

one dump say answer is A, other dumps is C

According to Cisco:
CLI command types
xStatus: these commands return information about the current status of the system. Information such as current calls and registrations is available through this command group.
xFeedback: these commands provide information about events as they happen, such as calls and registrations.

What do you think guys?

… real time call info…
xFeedback – …events as they happen such as calls…

Logically answer is C

Thanks Pit

Thank you Harper
Awesome dumps
Passed too

When you add third party call what button you should press?
A. TRANSFER
B. MERGE

please help
where can i find a valid dump for 210-060 exam

QUESTION 341
A Cisco EX60 is connected to the network, but users cannot make calls and the device is
unregistered. The voice engineer configured the device on Cisco Unified Communications
Manager. Which two options are causes of this problem? (Choose two.)
A. *SIP URI is not configured correctly.
B. H.323 parameters are not configured correctly.
C. IP address is in a different subnet.
D. *No user is associated to a device.
E. *SIP proxy is not configured correctly.
Answer: DE or AE???????

Hi! Finally PASSED 210-060 and 210-065 recently!!!

210-060 passed with 9xx/1000 (its passing score is 860/1000 now)!

I used the NEW version PassLeader 210-060 (287q~~~NEW VERSION DUMPS) and 210-065 (390q~~~NEW VERSION DUMPS) dumps, valid enough for passing now!

Good Luck!

P.S.

Part of PassLeader 210-060 dumps and 210-065 dumps are available here:

210-060 dumps:

http://bit.ly/210-060-dumps-online

(287q~~~NEW VERSION DUMPS)

210-065 dumps:

http://bit.ly/210-065-dumps-online

(390q~~~NEW VERSION DUMPS)

Good Luck!!!

failed PassLeader no longer valid dumps

NEW version PassLeader 210-060 (287q~~~NEW VERSION DUMPS) and 210-065 (390q~~~NEW VERSION DUMPS) dumps

210-060 dumps:

http://bit.ly/210-060-dumps-online

(287q~~~NEW VERSION DUMPS)

210-065 dumps:

http://bit.ly/210-065-dumps-online

(390q~~~NEW VERSION DUMPS)

Please anybody can help with a valid Dump for Cisco CICD 210-060 Exam
anybody can share it
Thank you in advanced

@Mio

QUESTION 341
A Cisco EX60 is connected to the network, but users cannot make calls and the device is
unregistered. The voice engineer configured the device on Cisco Unified Communications
Manager. Which two options are causes of this problem? (Choose two.)
A. *SIP URI is not configured correctly.
B. H.323 parameters are not configured correctly.
C. IP address is in a different subnet.
D. *No user is associated to a device.
E. *SIP proxy is not configured correctly.
Answer: DE or AE???????

For me its AE…Others, please need your input…

Regarding UDP ports on MCU:

Quote:

“Incoming ports
FTP – TCP:21 + TCP ephemeral (i.e. dynamic rather than fixed) ports used for passive mode
HTTP – TCP:80
HTTPS – TCP:443
H.323 – TCP:1720 + TCP ephemeral ports for incoming calls
RTSP – TCP:554
Windows Media Player streaming – TCP:1755
SNMP – UDP:161
Outgoing H.323 calls involve TCP connections from TCP ephemeral ports to TCP:1720 and a number of TCP ephemeral ports
Outgoing SIP TCP calls involve connections from TCP ephemeral ports to TCP:5060
Outgoing SIP TCP calls involve connections from TCP ephemeral ports to TCP:5061
Outgoing SNMP traps are sent from UDP ephemeral ports to port 162
Media (including audio, video and FECC messages) is UDP from ephemeral ports to ephemeral ports.
The Cisco acquired TANDBERG/Codian products and the Cisco TelePresence Serial Gateway Series allocate ephemeral ports in the range 49152 to 65535*. It is possible to change the ports on which these products receive and establish connections. For instance, by default Cisco acquired Codian products listen for H.323 calls to port 1720 and web browser connections to port 80 but these can be changed (go to Network > Services).
Outgoing ports
RAS – UDP:2222 for gatekeeper client messages and UDP:1719 for the built-in gatekeeper server (if enabled) …
…
This article applies to the following products:
Cisco TelePresence IP GW 3500 / MSE IPGW blade
Cisco TelePresence IP VCR 2200 / MSE VCR blade
Cisco TelePresence ISDN GW 3200 and 3241 / MSE 8310 and 8321 ISDN blades
Cisco TelePresence Serial GW 3340 and Serial GW MSE 8330
Cisco TelePresence MCU 4200 / MSE 8420
Cisco TelePresence MCU 4500
Cisco TelePresence MCU 5300
Cisco TelePresence MSE 8050 Supervisor
Cisco TelePresence MSE 8510 blade
Cisco TelePresence Server 8710 and 7010
Cisco TelePresence ConferenceMe”